Question about 1997 Chevrolet Camaro

2 Answers

Need to replace rear turn signal socket in a 97 Chevy Camaro. Attempted to purchase the part and there seems to be two different parts for that year and yet none of them seem to match. My socket has two wires while the most similar of the two has 3 wires.

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,118 Answers

I would say the extra wire is a ground. i found this when i bought a set for my classic witch is good, because you can use that wire and ground it right to the body or frame, first find witch 2 work your lights (unless there color coded to your harness)most of the time the ground wire will come out of the plug close to the edge. it should be either black or white. the extra wire should not be a problem as long as you get the right two for your lights. then you can either ground the extra wire or tape it off. good luck. OLD SCHOOL.

Posted on Jan 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Well i would either cut the scocket out and take it to a good parts shop they can look it up in there book other wise hit up the junk yards.

Posted on Jan 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On my 1994 chevy camaro,my steering column is bad.What range of years will fit?

If your talking about slack in the tilt part ,,, you can tightin it up,,, you will need a steering wheel puller and torx type sockets not sure the size ,,, once you get the steering wheel off ,horn assy out turn signal assy out,, the are 3 torx bolts that tightin it up ,,,remove bolts and use green lock tight on threads,,, reinstall and tightin ,, will never loosin agian if you use green lock tight

May 09, 2015 | 1994 Chevrolet Camaro

1 Answer

97 Camaro z28 automatic shifter

It has second gear start. To activate and provide extra traction when pulling out of snow and muddy ground. z28 have positive traction rears.

Jul 27, 2017 | 1997 Chevrolet Camaro

1 Answer

How do i change the front turn signal bulb on a 2001 Chevy Camaro

The headlamp needs to be removed first. Then the bulb socket can be rotated and removed.

Aug 10, 2010 | 2001 Chevrolet Camaro

2 Answers

When I go to turn on my lights on my 97 chevy

most vehicles wire the dash lights in with the rear stop lights to warn the driver of the problem they cannot see. check the fuse for your rear stop and tail lights. had this problem on my vehicle too.

Mar 26, 2010 | 1997 Chevrolet Camaro

3 Answers

1992 chevy s10 no brake lights or turn signals

Check the front and rear (although probably the rear) turn signal bulb socket for corrosion and/or water intrusion. If you find corrosion attempt to clean (but you will probably have to replace the socket and bulb). For water intrusion you will probably have to replace the break lamp assembly.

Aug 02, 2009 | 1992 Chevrolet S-10

2 Answers

Need new rear end for a 1996 Chevy Camaro (interchange options?)

camaro firebird and transam axles are what i would go for. remember lots of people change out the ratio just look for one with posi it will bolt right up if the ratio is wrong it will only affect speedo and fuel economy a little bit. this can also be changed easily with your ring and pinion out of the old one if need be.

May 18, 2009 | 1996 Chevrolet Camaro

2 Answers

Hi i have a 2002 chevy camaro and the turn signals will not blink

You need to replace the flasher. I'm not sure where it is located, but I can look it up if you need me too

Apr 01, 2009 | 2002 Chevrolet Camaro

2 Answers

97 camaro turn signals fail to work

sounds like two problems. the front turn signals operate through the drl module. It's behind the radio. if you cut and splice the dk. blue to dk. blue w/ white, lt. blue to lt. blue w/ white on the black connector it will bypass the drl but all other functions will work. some say to disconnect the blue connector to bypass however this will discontinue other features, e-brake indicator, rear hatch button, ect. As for the rear light, i would check the rear lamp harness connector behind the interior plastic drivers side for power on the right signal feed and the splice ground.

Mar 21, 2009 | 1997 Chevrolet Camaro

Not finding what you are looking for?
1997 Chevrolet Camaro Logo

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides