Question about 1997 GMC Yukon

Open Question

How do I re-install Clip to brake booster at brake paddle on a 1999 chevy tahoe not sure how the clip goes back on can someone help?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Brake Light Switch clip on 94 GMC Pickup

My 1996 Brake light clip needed to spread open with a screw driver(some what like a round spring) and with another screw driver push the switch up the pin. The switch will push the clip off the Pin. The pin has a head that needs to clear clip while the spring clip is spread open. It took me a while to figure out.

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I remove the brake booster linkage from the brake pedal?


the fsm covers this. (fact.serv. man)
ill paste the words, the book is free. to read.
booster out steps are there in chapter BRAKES
http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service
chapter 5
page 22
quote
POWER BRAKE BOOSTER REMOVAL
(1) Loosen but do not remove nuts attaching master
cylinder to booster (Fig. 3).
(2) Remove instrument panel lower trim cover.
(3) Remove retaining clip attaching booster push
rod to brake pedal (Fig. 4).
(4) Remove bolts/nuts attaching booster to dash
panel.
(5) In engine compartment, loosen vacuum hose
clamp and disconnect vacuum hose from booster
check valve (Fig. 5).
(6) Remove master cylinder attaching nuts and remove
cylinder from mounting studs on booster
(7) Carefully move master cylinder aside and remove
booster.
end

the clip is here.
the book is free, to read, and posted over 100 times now...


26142841-rrsfqd2upyiwrqbf5erfo4d2-4-0.jpg

Mar 27, 2016 | 1993 Jeep Wrangler

1 Answer

How to replace brake light swtch in a 1999 chevy tahoe


The switch is attached to the brake pedal. Remove the wiring connector and the switch will either have a clip securing it or will be held in place with a plastic bushing. If a plastic bushing is used, a gentle pull will be needed to remove the switch. Install in reverse order and check brake light operation for switch operation/adjustment

Jun 07, 2015 | 1999 Chevrolet Tahoe

1 Answer

How do I replace the brake switch on 98 C 1500 Chevy on brake pedal above steer column and the switch retainer clip


I just bought a 98 2500. Brake switch works, but I don't have the clip to keep switch inplace (which is on a peg attached to brake pedal). I just need the clip. I assume it would be a moon shaped clip that snaps on the end of the "peg." Once white brake switch is inserted onto the peg (swicth has a whole in it that fits onto peg) then clip snaps onto end of peg left exposed after brake switch is in place. As you apparently know, If that swicth slides off the peg or is bad, you can't put it in gear.

Feb 05, 2013 | Chevrolet 1500 Cars & Trucks

1 Answer

1999 Chevy Tahoe will not go into park at all all other gears work but feel loose


there is adjustment down on the ******. I will send you a picture, what you will need to do it put on the e brake,and block the tires. on the drivers side of the ****** the shift cable is located, pop off the cable from the arm and pull the white clip, when push the arm foward that is park,and then easily pull the cable to the arm and put back the white clip10_30_2012_8_31_59_am.gif

Oct 30, 2012 | 2000 Chevrolet Tahoe

2 Answers

My 1995 Chevy Tahoe brake light switch wont stay in position and the brake lights stay on. I replaced the switch and had the same problem.


Brake Light Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Disable the SIR system (if equipped).
  3. Remove the clip (R/V Series) or unclip the switch (C/K Series) and unplug the electrical connector from the brake light switch.
  4. Remove the switch.
  5. Installation is the reverse of removal.
prev.gif next.gif

Oct 07, 2010 | 1995 Chevrolet Tahoe

1 Answer

How to remove the retaining clip on the brake


Bear with me on this. It's a relatively simple clip (once you know how to remove them) but somewhat difficult to explain properly via the internet. But here goes. It may help if you draw it like this:

On a piece of paper draw a half inch line (don't lift the pencil/pen) up to down. Go right an inch and a half, down 1/16, left 1 1/4, down 1/8. Place the eraser end of the pencil to right of the 1/8 up against the 1 1/4. Got it?

Should form a type of a "T". Insert a flat screwdriver between the top of the pencil and the clip. If you twist the screwdriver it will lift the 1/8 part of the clip over the eraser permitting you to slide the clip off the shaft.

All I could think of...Hope that helps. Thanks for using FixYa.

Apr 03, 2010 | 1998 Chevrolet Tahoe

2 Answers

Having trouble with the brakes on my '90 Ford ranger. Replaced the master cylinder and still have very little braking power. Any help would be appreciated!


***Seek out professional help this vehicle is not safe to operate.***


Check the vacuum line going to the brake booster.

This is the big round chamber behind the master cylinder.

Hope this tip helps.

R/
David

Jan 23, 2010 | 1990 Ford Ranger SuperCab

2 Answers

How do you install a brake booster on a 82 chevy silverado


If you are indeed sure that you need the bootster, (you should hear a pronounced hissing sound from within the truck while depressing the pedal) it is a simple procedure. Remove the circlip or pintle type clip retaining the shaft to the pedal. Grab a flashlight and locat the four mounting nuts for the booster from inside the vehicle while lying on your back. Loosen theses slightly. Remove the master cylinder from the booster without removing any brake lines from the master cylinder. Leave the master hanging carefully in front of the booster. pull it gently towards the front of the master and away from the mounting bolts. Go back inside under the dash and finish removing the booster mounting nuts. Take note if there are any washers anfd don't allow them to fall beneath the floor carpet. Insallation is the reverse of removal. Thank you, Dana

Oct 04, 2009 | 1983 Chevrolet Silverado

1 Answer

How to replace a brake booster in 1995 buick riviera? my brakes are hard to push and almost impossible to brake. a hissing sound like a air leak comes from the booster.


undo the the vacuum hoses and make sure you make a diagram of where each hose goes. move them out of the way.

undo the four bolts that attach the master cyclinder to the booster. use a wire coat hanger or just wire to support it. you don't want to bend or break the brake lines.

undo the four bolts that hold the booster to the firewall. carefully pull it away from the firewall. you will see a small are there with a clip. remove the clip and unhook the arm.

reverse those instructions to put it back together

However BEFORE you do that. Make sure that none of the vaccuum hoses are leaking.

please take a moment to rate this solution. thanks

robert

Sep 04, 2009 | 1995 Buick Riviera

2 Answers

Power Brake Booster 1998 Chevy K-1500


there is a lock clip use a small straight screwdriver pull out the center and slide off the clip

Oct 01, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
1997 GMC Yukon Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...