Question about Cars & Trucks

Open Question

Wilms VAL-6 heater how to bleed - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the a/c expansion valve located on 2006 range rovrer


1 - Radiator
2 - Thermostat housing
3 - Radiator bottom hose
4 - Viscous fan
5 - Water pump
6 - Radiator top hose
7 - Heater return hose
8 - Coolant supply hose
9 - By-pass hose
10 - Radiator bleed (purge) hose
11 - Bleed (purge) hose, thermostat housing
12 - 'Y' piece ejector
13 - Expansion tank
14 - Heater rail
15 - Heater unit
16 - Heater feed hose
17 - Intercooler
18 - Air cleaner
19 - Air feed hose
20 - Turbocharger
21 - Charge air supply hose
22 - Cooled charge air supply hose
23 - Exhaust manifold
24 - Engine oil cooler
25 - Feed pipe, engine oil cooler
26 - Return pipe, engine oil cooler
27 - Oil filter
26264875-o0qmuaeri1ktexfeuzrayee3-3-0.png

Aug 22, 2016 | 2006 Land Rover Range Rover

1 Answer

How do i bleed heater


1997 Oldsmobile Bravada heater core removal - YouTube

? 3:22
www.youtube.com/watch?v=7OwIuiYqt0s

Oct 25, 2012 - Uploaded by Lloyd Ankney
1997 Oldsmobile Bravada heater core removal ... How can I replace a blend door actuator on a 99 Bravada? .... Heater core replacement 2000 S10 4.3L ( slideshow picture ) - Duration: 3:52. by Joe Lleras 169,585 views. 3:52.

Oldsmobile bleed air in heater core Cars & Trucks ... - Fixya

www.fixya.com > Forum > Tags > bleed air in heater core > Cars & Trucks
If your cooling system has any bleed screws incorporated, crack them once in a while as well. 2000 Oldsmobile Bravada heater blows cold air. Had a new heater .

Oct 25, 2015 | 2000 Oldsmobile Bravada

1 Answer

How do i bleed coolant system on mg zr 2003


after filling cooling system there is a bleed screw on the coolant pipe that runs round the end of the cylinder head.rh has you look under bonnet 8mm head,loosen that or remove it may be blocked! the heater can give problems if you have completely drained the system or have had a major leak it may be airlocked! make sure the heater is set to hot, run engine until coolant flows from bleed screw, close bleed screw, remove coolant cap carefully,and top up.leave to stand for 20 mins or so. re top up run engine @2500 revs if the heater is cold and you have no bleed screw on the heater hose. there is a valve that fails in the heater hose bypassing the heater matrix.that may need replacing if the heater is cold, hope this helps.

Mar 08, 2015 | MG Cars & Trucks

1 Answer

How to bleed an air pocket out of a heater line


there should be bleed screws where the rad hoses join to water pump,thermostat housing ,also run engine with the heater turned to full heat when doing the bleeding as can get air pocket in heater matrix

Apr 21, 2014 | 2004 Dodge Ram 1500

1 Answer

Blowing cold air engine overheating


You will need to bleed the coolant system. There will be a bleed screw on the left hand side of the manifold. There is not enough coolant to flow through the heater core.

Mar 23, 2014 | Chevrolet Cars & Trucks

2 Answers

I have an audi 97 a4 6 sylander and i had to change the metal pipe wich transfer water from reservor to termostat housing do i need to bleed the system after fix and soo wher is the bleeding valve thanks...


you dont have to bleed the water it automatically takes out the air when it runs and the thermostat valve opens check the level again after a run of 5 miles or when the temp is in the middle

remember not to check when the engine is hot

Feb 07, 2011 | 1997 Audi A4

1 Answer

Had breaks bleed and 3 days later no break again. shop told me that it needed a break fluid val some one else said break line which is it somebody help me plz


check to see if your wheel cylinders are leaking, then check for leaks at the brake lines, if no leaks, have the brakes bled properly there maybe air in the lines. you have to do both wheels, front to front, back to back, check master cylinder.

Apr 09, 2009 | 1993 Dodge Spirit

2 Answers

Heater is not blowing hot air


Do you have a sloshing sound in your dash? You may have an air pocket in your coolant lines that you need to bleed. I had this problem about 6 months ago in my '05 Impala

Mar 12, 2009 | 2005 Chevrolet Impala

1 Answer

NEED SERIOUS HELP


there is a inline val.. that works off of vaccum this val is close and you will not get heat when it is close it is on the inline the pin that work it usely breaks

Feb 23, 2009 | 1997 Ford Explorer AWD

1 Answer

Heater


sounds like your thermostat could be stuck...they are very cheap...

Nov 20, 2008 | 1996 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...