Question about Vauxhall Vectra

Open Question

Vectra 1.9 cdti head bolt torque settings - Vectra Vauxhall Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mironate
  • 19 Answers

SOURCE: torque settings

  1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.

Posted on Aug 06, 2008

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

darrencasey0
  • 1 Answer

SOURCE: head bolt torque for a 1996 ford ranger 2.3liter

it is in the haynes repair manuel and chad is right

Posted on Apr 05, 2009

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

2 Answers

I have a 1998 Holden Astra eng noEL20B24119 and want to know the Head bolt torque settings and sequence. The engine is the transition model with twin tappet cover seals. has the torx star headed bolts.


I cannot find a EL20B in my data,but all Astra listed had the same head sequence as shown:

10 6 2 3 7

9 5 1 4 8

the torque specs for the C20XE,C20NE,X20XEV were all
25nm(18lb/ft),-then 90 deg,-90deg,-90deg.
Z20LET were as above plus an additional 15deg.
Same data for smaller and larger engines(except a couple that were 45deg instead of 15)
Make sure that you replace the head bolts with new,they are torque to yield bolts that are designed to stretch to 'plastic' state,and should not be reused.
Put grease(graphite if you have it) under bolt heads and washers,oil the threads.
Usually the head sets come with the torque specs.
I hope this helps you.

Apr 02, 2011 | Honda Accord Cars & Trucks

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

1 Answer

Torque settings for a holden rodeo 3.5 ra. Head


stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Dec 03, 2009 | 2004 Isuzu Rodeo

1 Answer

Head bolt toqure


Hope this helps, from autozone site. Curt
Application:
Cylinder head bolt torque sequence

Note :
Torque sequence:
---------
front | 3 1 6 |
of | |
vehicle | 5 2 4 |
---------
Step 1: Lightly oil cylinder bolt threads & washers
Step 2: Torque to 22 Ft/Lbs
Step 3: Torque to 51 Ft/Lbs
Step 4: Loosen all bolts 180 degrees
Step 5: Loosen all bolts 180 degrees
Step 6: Torque bolts 1 & 2 to 25 Ft/Lbs
Step 7: Torque bolts 3, 4, 5, 6 to 11 Ft/Lbs
Step 8: Turn all bolts an additional 80 to 90 degrees
Step 9: Turn all bolts an additional 80 to 90 degrees
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper Torque.

Apr 24, 2009 | 1995 Subaru Legacy

2 Answers

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Angle Torque settings head bolts


Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Jan 28, 2009 | 2000 Renault Sportwagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

579 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vauxhall Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79851 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you a Vauxhall Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...