Question about Cars & Trucks

1 Answer

I took the breaks off to put in a new cv joint on a mazda mx3 and some peices came out now dont know were they go

Posted by on

Ad

1 Answer

Look at the other side

Posted on Nov 27, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1619 Answers

SOURCE: i got 1993 mazda mx3 i changed cv joints and my

there should be a square divet one low and one high on the side of the transmission that you can unscrew and refill with the gear oil.

Posted on May 09, 2010

  • 5 Answers

SOURCE: CV Joint Replacement '92 Mazda mx3

I suggest getting a service manual. If you've never done one before, a book will explain a vehicle specific order of operations. Chiltons or Haynes are good. consider it $20 insurance. Good Luck.

Posted on Aug 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't budge outer cv joint Mazda MPV 1991


the outer cv joint is separable
you have to take the complete drive shaft out of the vehicle first to do it
It is not a simple process to break the joint down and you will need mechanical skill, a good off set vice and a heavy hammer
it is more cost effective and less frustrating to simply have drive line specialists replace the shaft for you

Aug 01, 2016 | Mazda Cars & Trucks

1 Answer

Mazda MX3 "Charge" light


You can use VCM IDS for Mazda to have a check

Jul 19, 2013 | 1992 Mazda MX-3

1 Answer

How do i remove the front drive shafts on a 97 mazda b2600 4wd to replace the cv boots?


When you did the ball joints you should have pulled the axles

I would guess that you know the axle nut has to come off & that
in most cases you break the bottom ball joint loose, so you can
get the axle out of the steering knuckle

So I will guess you can't get the axle out of the trans

You use a long pry par,3 foot or more & put the end against
a piece of wood, so as not to pry on the aluminum trans case

Then you pop it out with the pry bar.
You don't pry on the axle ,you use the side of the pry bar
to bang it with the end against the wood

Sep 26, 2012 | 1986 Mazda 323

1 Answer

How do i remove the boot of a CV axle/joint and its stuck in the motor or transmission..... I'm a girl give me a break LOL


ok girl i guess its out of the knuckle and stuck in trans dont worry the retaining ring is stuck . use a large screwdriver or pry bar and big hammer. place in crack at axle trans and hit or get at a angle and hit till pops out . had one in jag took hours to pop out ring was broken on shaft and holding in. just stay at it and it will come out.

Aug 05, 2012 | 1997 Mazda Millenia

1 Answer

I am hearing a clunk when breaking with in town driving..not all the time. Took to repair shop, put on new struts in front. Still hearing the clunk occasionally.


It sounds like a cv joint noise how dose the steering wheel feel dos it shake side to side when brakeing truthfuly im not that formilar with your car but its a front end problem. New struts would help but not completly elimitate it. Im not sure if the engine is inverted on your vehicle is it front wheel drive if so its likely cv joints

Nov 07, 2010 | 2004 Chrysler Concorde

2 Answers

1992 Mazda MX3 driver side cv axle won't come out. Took off nut axle stuck and won't come out. How can I get it out?


Get a good pry bar and wedge the bar between the CV shaft and where it goes into the tranny.You should be able to pop it out.If not rotate the shaft and repeat untill it lets go.It is only held in place by a round clip on the shaft inside the tranny.Be patient its been there a long time. Good Luck

Oct 24, 2010 | 1992 Mazda MX-3

1 Answer

I got 1993 mazda mx3 i changed cv joints and my gear oil leaked out of tranny.. i cant figure where or how to refill


there should be a square divet one low and one high on the side of the transmission that you can unscrew and refill with the gear oil.

May 09, 2010 | 1994 Mazda MX-3

1 Answer

CV Joint Replacement '92 Mazda mx3


I suggest getting a service manual. If you've never done one before, a book will explain a vehicle specific order of operations. Chiltons or Haynes are good. consider it $20 insurance. Good Luck.

Dec 14, 2009 | 1992 Mazda MX-3

2 Answers

I had my cv joints changed out and now my knocking sound is worse


Is the knocking only on turns from the front and it is a fast continual knocking?
If the installation was correct.......sounds like the CV joints are possibly defective.
When changing CV joints.......always put in complete shaft assemblies that use NEW joints....not rebuilt joints.The price is almost the same.

Sep 06, 2009 | 1995 Mazda 626

1 Answer

How do you replace a cvc joint in a mazda mx3 1192


You will have to take the front suspension loose enough to pull it out of the way to get the CV joint out

Aug 01, 2008 | Mazda MX-3 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...