Question about 2001 Saturn S-Series

Open Question

2002 saturn sc1 hard shifting problem - 2001 Saturn S-Series

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fischmilch
  • 96 Answers

SOURCE: 99 Saturn SC1 ''Service engine soon'' light is on.

Did you get the code that triggered the SEL? If you know that, it will be easier to diagnose your problem. You can do it without a tool on the old saturns. Just need a paperclip. :

Use a paper clip to jumper Terminal A and B of the ALDL *Assembly Line Diagnostic Link* which is above your left knee.
Terminal A is an interal ground and is the top right terminal in the connector. Terminal B is directly adjacent and to the left of Terminal A.

Turn the ignition to ON.

All codes are 2 digits between 11 and 99. Codes are displayed on the SES light by flashing the light with short and long pauses to distinguish digits of one code from digits of another. The short pause is used between digits of the same code, long pauses are between codes. Also, each code is flashed three times before going to the next code.

For example, the sequence of code 12 will be: flash, pause, flash-flash, long pause, then repeat 2 times. If Code 12 is not displayed, the self-diagnostic pogram i snot functioning properly.

If only Code 12 is displayed, no system malfunctions have been stored.

Any existing system fault codes are displayed in order from low to high, except for Code 11.

On vehicles with an automatic transaxle and on which exist stored transaxle codes, Code 11 will be displayed last, then the SHIFT TO D2 light will begin flashing transaxle codes of flags.

When all engine codes have been displayed, Code 12 will flash again.

Diagnostic Codes
11. Transaxle Codes present
12. Diagnostic System Check
13. Oxygen sensor, circuit open or not ready
14. CTS circuit, out of range high
15. CTS circuit, out of range low
17. PCM fault, pullup resistor
19. 6x signal fault, no 6x signal between reference pulses
21. TPS circuit, out of range high
22. TPS circuit, out of range low
23. ATS circuit, out range low
24. VSS circuit, no signal
25. ATS circuit, out or range high
26. Quad Driver output fault
32. EGR system fault
33. MAP sensor circuit, out of range high
34. MAP sensor circuit, out of range low
35. IAC valve, rpm out of range
41A EST circuit open
41B EST circuit shorted
42A Bypass circuit grounded
42B Bypass circuit open
42C Bypass circuit shorted
41. EST bypass, open or shorted
42. EST bypass, open or shorted
43. ECS (knock sensor) circuit open or shorted
44. Oxygen sensor indicates system lean
45. Oxygen sensor indicates system rich
46. Power steering pressure switch circuit, open
49. Idle rpm out of limit high (vacuum leak)
51. PCM memory error
55. A/D converter error in PCM
81. ABS message fault (1993 vehicles with TCS)
82 PCM internal communication fault


Diagnostic Flags
27. Quick quad driver output fault (1993 only)
48. Reference imput intermittent or noisy
52. Battery voltage out of range
53. ESC knock present
54. Five volt reference ground
58. Battery voltage unstable
61. 6x signal fault
63. Option check sum error
67. Handwheel sensor circuit fault
71. Cooling system temperature high
72. Coolinng system temeprature low
73. CTS sensor unstable
74. CTS/transaxle temperatuer sensor ratio error
76. ATS sensor unstable
83. Low coolant (1993 only)

Posted on Mar 27, 2009

Ad
  • 186 Answers

SOURCE: bleed the clutch

No way to bleed the clutch system.You need to buy a clutch master/Slave assy from saturn.Comes completely full of fluid & ready to install.It has retainers to hold slave pin in place until fully installed.Once installed you push the pedal & you will hear a faint click which is the slave retainer breakaways relieving.No other way to bleed although aftermarket parts house will sell you individual pieces.hope this helps

Posted on May 21, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 saturn shifting hard what do i do boys

Check the transmission fluid level and condition. Make sure the level is correct, if it is then it may be time for the transmission for service. The transmission service time is every 30,000 miles, and if it has not been serviced the Transmission line pressure solenoid could be gummed up with dirt. Have the transmission fluid flush and the transmission oil filter replaced and hope that helps. Hard shifting is a sign of fluid restriction in the valve body in the transmission and will lead to a costly transmission failure. Good luck and keep me posted, the other thing to that would give you a hard shift is a bad throttle position sensor. But that should have given a check engine or service engine light on. 

Posted on Jul 02, 2009

  • 396 Answers

SOURCE: 1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear

Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Posted on Jul 01, 2010

  • 1 Answer

SOURCE: transmission shifting very hard

  • 2002 saturn auto trans has 3 different model/ DO YOU KNOW THE NAME?

Posted on Jan 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why saturn shifting to reverse is a hard kick


most obvious cause could tbe the gearbox oil level ,its needs about a litre i would imagine ,providing that it has a dipstick to check the level of course

Jul 19, 2014 | 1993 Saturn SC1

1 Answer

1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear


Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Jul 01, 2010 | 1998 Saturn SC

1 Answer

95 saturn sc1 all of a sudden had engine light on and the idle just went way low, also effects how tranny shifts, but will barely stay running in gear with brake on. Sometimes it starts idling fine and...


You either have a bad engine coolant temp sensor & connector.Located under upper radiator hose at cylinder head Yellow & black wire.Original sensor is ceramic & replacement will be brass from saturn.Also you may check for vacuum leaks at PCV hose & valve.Hope this helps

May 15, 2009 | 1993 Saturn SC1

1 Answer

93 saturn sc1


Try pulling the engine coolant temp sensor, They often crack not sure why but the ceramic tip cracks makes the car hard to start, the car's idle may race while shifting gears, and often smokes. The sensor is on the right side of the engine when looking at it on the head. Easy to change and get too

Jan 13, 2009 | 2002 Saturn VUE

1 Answer

93 saturn sc1


Try pulling the engine coolant temp sensor, They often crack not sure why but the ceramic tip cracks makes the car hard to start, the car's idle may race while shifting gears, and often smokes. The sensor is on the right side of the engine when looking at it on the head. Easy to change and get too

Dec 28, 2008 | 1993 Saturn SC1

1 Answer

2002 Saturn sc1 Big trip....


Depends on how heavy a trailer. I wouldn't advise trying.

Jul 22, 2008 | 2005 Saturn SC1

Not finding what you are looking for?
2001 Saturn S-Series Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...