Question about 1999 Toyota Camry
Removing front passenger side fender
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Pull off the triangle thing.
On the door, at the front edge, there should be 2 plastic caps. Remove them. Under the caps there are screws. Remove them.
On the rear of the door panel, above the latch, are 2 round things, with a smaller round thing in the middle. Press on the inner round thing, and pull the pin assemblys out.
Do you have a light on the door panel at the bottom? If so, pry it out with a small screwdriver (it's just a "press-fit"), and remove the wire connector.
Under the arm-rest, remove the big phillips screw that is hidden, about an inch back from the outer edge of the panel. You will see the hole.
Under the arm rest, remove the tiny plastic trim cover, remove another big phillips screw.
Remove the door handle: Remove the phillips screw. Slide the handle forward or backward to release it from the door metal. Undo the clamp from the lock rod to the handle.
Remove any screws at the very bottom of the panel, if there are any.
Starting at the bottom of the panel. pull straight out, to defeat the plastic clamps tht holds the panel to the door metal. Once the panel is loose, pull it up a bit to remove it from the window opening retainer. Finally, inside the panel, unplug the wiring harness to the window switch assembly.
If you need any more info, please comment back. And, Thanks for the FIxYa.
Posted on Nov 14, 2008
Hi there :
if you remove the knobs you will see there is some flat nuts that need to be removed remoive them and there should be able to remove the faceplate
Posted on Feb 17, 2009
Yes, you have to remove the door panel.
Remove the 2 plastic protectors on the front edge, and remove the 2 brass colored screws. Next, remove the push pins from the latch side. Push in, and pull out the whole thing. Next, under the armrest, remove the screw. Lift up the power windoe control, being careful to not break the plastic retainer tab. Remove the screw under the window control. Starting at the bottom, pull out the panel, and, when all of the clips are loose, pull the panel straight up. It is best to do this with the door panel as warm as possible, like in a heated garage. Doing this outside in the cold will break all of the plastic retainer clips; they are quite brittle whn cold.
I hope this helps
Thanks for choosing FIxYa for assistance. A FIxYa rating (4 blue diamonds) would be greatly appreciated.
Posted on Feb 23, 2009
this sounds correct, however, if you go to autozone.com, the have access to free online manuals, giving you step by step instructions on how to remove. you will need to register and provide some info about your vehicle. it is FREE! the manuals are in the do it your self area. Good Luck!
Posted on Sep 13, 2009
To remove mirror pry off inside triangle panel(black) which exposes 3 nuts which are removed with socket wrench. Detach wire harness and pull out mirror assembly. To replace insert new mirror screws thru assigned holes and reconnect wire harness and tighten nuts to snug. Push inside triangle panel back into place and you're done! It's that easy.
Posted on Jan 06, 2010
Tips for a great answer:
Jan 05, 2018 | Dodge Durango Cars & Trucks
Dec 29, 2015 | Hyundai Motor 2003 Elantra
Jul 20, 2014 | 1998 Buick LeSabre
May 12, 2011 | 1997 Volkswagen Jetta
Apr 16, 2011 | 1998 Lincoln Mark VIII
Nov 07, 2010 | 2000 Dodge Intrepid
Apr 03, 2010 | 2003 Ford Focus
Mar 15, 2010 | 1998 Ford Contour
Jul 07, 2009 | 2000 Ford Taurus
429 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: