Question about 1996 Ford Explorer

1 Answer

I need a picture of the 02 sensors on a 1996 ford explorer

I need a picture of the engine and where the oxegon sensors are on a 1996 ford exploreer eddie bauer 4.0 l

Posted by on


1 Answer

No you don't

You have front or upstrean O2 Sensors before the exhaust
converters & downstream or monitors in the converter outlets

You obviously have wires going to them

If you went under the vehicle you wouldn't be asking

Posted on Nov 27, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: overdrive transmission

this is the old style transmission code you have a problem with a solenoid inside the transmission go to a transmission shop to read and replace the solenoid only not a rebuild usually

Posted on Jun 12, 2008

  • 8 Answers

SOURCE: can not find the fuel

on right or left in rear inside a door near jack

Posted on Jul 08, 2008

  • 1 Answer

SOURCE: Ford Explorer Oil change rest message

Turn ignition on. Don't start the car. When the message shows up press setup. It will tell you to press reset to reset the oil life to 100 %.

Posted on Aug 25, 2009

  • 811 Answers

SOURCE: 1997 Ford Explorer eddie bauer edition audio

buy manual

Posted on Sep 12, 2009

  • 65 Answers

SOURCE: The lower lumbar support on the driver seat will

the air lumbar is an air bladder in the seat that is inflated by an air pump. Either the Check valve in the pump has failed and not holding air in the baldder, or the bladder has cracked and is leaking. May be possible to find another seat at a junk yard that is the same as yours. Replacing the entire seat is simpler then replacing just the bladder and pump assembly.

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ford explorer p0059 code

P0059 .02 sensor heater control circuit draw. 02 heater resistance What this means is the 02 is shorted or open or ECM . 2nd bank sensor one. What concern me is rough accleration,either the ECM subsituted a value to protect the catalytic or you do have a engine miss and P0059 under rationality ,logic appeared.I have to say your solution is to replace 02 sensor on the second bank.To find the second bank stand in front of the vehicle the valve cover closest to the front is bank one the valve cover fartherst from the front is bank two.

Mar 08, 2012 | 2003 Ford Explorer

1 Answer

Where is the camshaftsensor on a1996 ford explorer with a 4.0

1996 Ford Truck Explorer 4WD 4.0L EFI 6cyl the Camshaft Position Sensor is located: Under hood, center, rear engine area,mounted on center upper rear of engineblock

Remember to rate this and comment.

Sep 13, 2010 | 1996 Ford Explorer

2 Answers

Transmission removal pictures for a 1996 ford explorer..i need to know how many bolts there are to remove the transmission from the motor

4x4 has seven transmission-to-engine bolts
4x2 has six transmission-to-engine bolts

You need to tell me though if this is an automatic or manual and 4x4 or 4x2 There are 3 different auto trannys: 4R44E, 4R55E then A4LD and 4R70W

Sep 06, 2010 | Ford Explorer Cars & Trucks

1 Answer

1996 ford explorer v8 forward o2 sensor bank one. How do you go about replacing this sensor?

As long as you know which one you are replacing it is very easy. Sometime these can be removed by a 22mm wrench but the best way to go is buying a oxygen sensor socket, the socket has a cut in it for the wires to slide in. You simply unplug the sensor and start the removal with the socket. It's easier to remove sometimes if the engine is warm. This keeps you from stripping the threads. When replacing, be sure the threads have anti-seize grease. I work for Bosch and run the line that produces 02 sensors. Buy the aftermarket because they are made the same way, with then same components. It may look a little different but it's just like the OEM if not better.

Jun 13, 2010 | 1996 Ford Explorer

1 Answer

2002 ford explorer check engine light on. codes po 171 po 300,1131,1151.seems to me that i may need bank1 and bank2 02 sensor

Check and clean the MAF (mass air flow sensor). you will need a #20 anti-tamper torx bit and some carburetor cleaner. Be careful with the sensor it is delicate.

Apr 21, 2010 | 2002 Ford Explorer

1 Answer

Where is the camshaft sensor located on a 1996 ford explorer 4.0 literand where is the egr valve located also

cam sensor is located rt side of engine half way up egr is left side of engine front ove valve cover

Mar 03, 2010 | 1996 Ford Explorer

1 Answer

I have a 96 Explorer. The engine light would come

clean the mas air flow sensor first and report.

Sep 10, 2009 | 1996 Ford Explorer

1 Answer

Check Engine Light On

have the 02 sensors checked

Jan 20, 2009 | 2001 Ford Explorer

1 Answer

I have error codes p0156 p0161

  Check the wire harness near the top of the engine in the rear. They were good for rubbing through on the trans fill tube bracket. Judging by the code you have 4 sensors. you would be interested in the drivers side rear sensor.

Nov 11, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
1996 Ford Explorer Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5675 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides