Question about Subaru Cars & Trucks

Open Question

Subaru outback 2001 glove box removal - Subaru Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 178 Answers

SOURCE: I have a 2005 Subaru

hello first thing to check is were the box mounts at the bottom of the door hinge assembly undo the screws you should be able to lift the door enough to release the lock inside goodluck

Posted on Sep 14, 2008

techbuster
  • 5081 Answers

SOURCE: how do u put timing belt for 2001 subaru outback

This is not your average timing belt replacement due to being a double overhead cam that is also an interferance fit.First remove cooling fans.2-Loosen drive belts and remove.3-Remove crank pully.4-Remove timing covers.You will see 4 cam sprockets.Theses sprockets contain single and double referance marks.You will be using the double referance marks.Rotate engine until the double referance marks are facing each other.This is to be done the same way that the American autos timing Chain systems are done but you will have 2 small double lines to line up not dots.The next step is the most important step and is of utmost imortance.THE CAMSHAFT HAVE TO BE LOCKED IN PLACE--FAILURE TO DO SO CAN RESULT IN BENT VALVES.The cam sprocket holders can be bought or rented.You can make your own as well by making 2 wedges with bolt through the middle.Slip in between sprockets and tighten enough to hold sprockets.Do not use excessive torque while tightening wedges sprockets are not made of steel but rather a composite material.Next you will have to remove the tenioner.The tensioner has to be retracted and pin istalled to hold in retracted position.The tension device has to be retracted with care or will be damaged.You can not exceed 50 pounds pressure on the plunger.The simplest method is to reract while still in vehicle, it takes 15 minutes to properly retract the plunger.By pulling up on the tensioner by hand with about 18 pounds of force --50 will be exerted at the plunger.When fully retracted insert pin to hold in reracted position.Next check to make sure that cam wedges are holding and no sprocket are trying to move,when satisfied remove one of the rollers at the bottom on the side where you left hand would be standing in front.Pull off belt.Replacement belt will have referance marksone line will go to crank sprocket face up others will line up with other sprocket marks.Reinstall roller followed by tensioner then pull pin you have holding tenioner retracted.Remove wedges.Reinstall covers fans belts.Do not be intimitaded by this replacement.Everything is very easy to get to.Be sure cams are locked and that damage is not done to tensioner and it is straight forward.

Posted on Nov 06, 2009

  • 176 Answers

SOURCE: How do you change the cabin filter on a 2001

Once your glove box is removed and out of the vehicle, you will see the HVAC casing. The access panel held in with 4 clips is what your cabin filter hides behind.
Please let me know if I may further assist you. -TXTEXAN

Posted on Mar 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the glove box housing to get to the blower behind it on a 2008 subaru outback


you might find the instructions for changing your cabin air filter will help. Look it up at cars101 DOT com .

Mar 01, 2015 | 2008 Subaru Outback

1 Answer

Subaru outback impreza - 07 heater blower noisy


its under the glove box facing up. you remove it by dropping it down.
there should be 2-4 screws and the drain hose

Dec 06, 2013 | 2007 Subaru Impreza Outback Sport Wagon

1 Answer

Where is the heater blower resistor located in a 2000 Subaru Outback? I've seen one reply in a forum saying it is to the left of the blower motor, but I don't know where that is either. I need to...


the blower motor is located under the passenger side of the dash. The blower motor resistor is located behind the glove box assembly. You will need to remove the glove box assembly and then you will see the resistor. It will have one connector with four or five wires and will be held to the HVAC unit with 2 screws.

Jun 23, 2011 | 2000 Subaru Outback

1 Answer

Where is the cabin air filter located? I want to change it.


the cabin air is located behind the glove box. there are about 6-8 phillips screws that secures the glove box. once the box is removed, you will see a rectangular access cover that flips open to the filter.

Apr 04, 2011 | 2002 Subaru Outback

1 Answer

How to change cabin air filter in a 2003 Subaru outback/


Your cabin filter is located behind the glove box.
First you will need to remove the glove box. Open the glove box, and on the left and right side on the inside, there will be a retainer that you will need to pull out. This will cause your glove box to fall forward, exposing all of the screws. Unscrew the 10 screws around the outer edge of the glove box, and pull the unit down and out of your way.
After the glove box is removed, you will be able to see the HVAC casing. You will see the access door to the cabin filter, held in with some clips. Disconnect the resistor connector that is in your way, then remove the four clips in order to access the filters.
Once you pull the filters out, you can install the new ones in reverse order. Make sure that the arrows on the filters are pointing up, and that the door is sealed properly when you close it back up.
Good luck and please let me know if I may further assist you. -TXTEXAN

Nov 28, 2010 | 2003 Subaru Outback

1 Answer

Change cabin air filter 2080 Subaru outback


Your cabin filter is hiding above/behind your glove box. In order to access the cabin filter, first remove the passenger instrument panel side cover. Next, open your glove box and there should be one clip on the left and right side of the glove box... remove those clips as well as the tether that is holding the glove box up. After the glove box falls forward, remove the upper storage box. You should now see the cabin filter access panel, which is held in with 5 or 6 screws. Remove the screws, pull the access panel out, and you should see the cabin filter. Reverse instructions for installation.
Please let me know if I may further assist you. -TXTEXAN

Nov 22, 2010 | 2008 Subaru Outback

1 Answer

How do you change the cabin filter on a 2001 Subaru outback? Removed glove box but don't see how to find it. Thanks Doug


Once your glove box is removed and out of the vehicle, you will see the HVAC casing. The access panel held in with 4 clips is what your cabin filter hides behind.
Please let me know if I may further assist you. -TXTEXAN

Mar 14, 2010 | 2001 Subaru Outback

1 Answer

Cabin air filter on a 2006 subaru outback limited


The cabin air filter is behind the glove box. The first thing you need to do is empty the glove box. (2) you need to remove the side panel that runs along the side of the shifter, it is a long panel and has on clip near the firewall, the clip will have a phillips head on it, just back it out and remove this panel. Then remove all the bolts (10MM) holding the glove box on, The glove box is will stay up because it has two hings that run into the sides of dash. All you need to do is squeeze the glove box untill it pops out and the glove box will be out. There is no need to unhook the wiring for the light bulb just let the glove box hang on the floor. Now you will see a black cover that is held on by 4 small metal clips, remove these and pull the cabin air filter out. when you reinstall the new one, make sure you put it in with the air flow arrows pointed in the right direction or else you will cause blockage. reinstall and enjoy your new heppa filter

Jun 19, 2009 | 2006 Subaru Outback

1 Answer

2001 Subaru Outback tail lights don't work


do you have a trailer hitch? if yes disconnect convertor box the light behind the dash should not be related bulb just out, also make sure bulbs you've changed are correct

Jun 09, 2009 | 2001 Subaru Outback

2 Answers

2005 subaru outback cabin air filter install


Yes the o5 outback has a cabin air filter and it is located behind the glove box. You have to remove the glove box, once you get it out of the way you will need to remove the 4 metal clips that hold it in place and make sure you put the filters in with the arrows pointing in the right direction for air flow. Other wise you will have restriction through the vents

Apr 11, 2009 | 2005 Subaru Outback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...