Question about 2001 Kia Sportage

Open Question

Location of purge solenoid valve on 2001 kia sportage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 833 Answers

SOURCE: 2001 kia sportage blower motor resister

Rule of thumb...unless you get a better answer:  look for a couple of wires on a small plate that is in the airflow of the fan on the heater/ac unit.  The resistor pack is always air cooled by the fan.

Posted on Nov 11, 2008

  • 3 Answers

SOURCE: 2001 kia sportage 4wd

replace vacuum hoses they are located just out side shock towers front end

Posted on Jan 17, 2009

  • 1 Answer

SOURCE: 06 kia sportage airbag control module

If your refering to the light on top of the dash that says "psgr air bag not connected" here;s the deal.

The module is activated when someone sits in the seat. Turn the key on and the notification will light. Go around to the psgr side of the car and sit in the seat and the light should go out.

Posted on May 03, 2009

  • 336 Answers

SOURCE: where is fuel filter on Kia 2001 sportage located?

Hi there,

Here is the exploded view of your fuel system, fuel filters are encircled..

32cdb89.jpg
Regards,
Jeep Brainy

Posted on Sep 15, 2009

  • 4044 Answers

SOURCE: how to repair a fuel tank pressure sensor in a

The Fuel tank pressure sensor or Fuel pressure sensor? The pressure sensor for the fuel line is located in the Engine compartment, although I don't have the exact location it is located on the fuel line. If your talking about the Fuel level sensor that is actually part of the Fuel pump assembly. You should pick up the Haynes Repair manual on your vehicle before attempting either repair.

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace the 2 ignition coils on 2001 kia sportage


This video is to show how to do a compression test, but it will help with dis-assembly, and shows where all parts are located. The only thing I didn't see, was removal of the center cover above the plugs, ans coils. Kia Sportage 2001 Compression Test Definitely a help for plug, and coil change on 2001 Kia Sportage.

Apr 26, 2014 | 2001 Kia Sportage

1 Answer

Where is the pressure valve on Xtrail


rectify loose/ cracked hoses. check if the canister is in the vicinity as it may have a problem with the purge valve / solenoid.

Jan 14, 2014 | 2000 Kia Sportage

1 Answer

How do you replace the evap. purge valve solenoid on 2005 kia sportage


The canister purge valve is a computer controlled solenoid valve that allows any stored fuel vapors in the charcoal canister to be recycled back into the engine combustion process. The valve is typically located on or near the throttle body. The canister purge valve is controlled by the power train control module (PCM). The canister purge valve is closed each time the power train computer runs the OBD-II (Onboard Diagnostic Generation II) EVAP monitoring self-test.--------------------------------------------------------------------------------
renault can clip

Jan 05, 2013 | Cars & Trucks

2 Answers

Where is the canister purge valve located on a kia sportage


in the rear near the fuel tank look for a black box its near that as well

Jul 09, 2012 | 2002 Kia Sportage

1 Answer

2002 Kia sportage with the code p0443


Hi Brittany:
The Evaporative Emissions System (EVAP) allows fumes from the gas tank to enter the engine to be burned, rather than vented into the atmosphere as an emission. The purge valve solenoid is supplied switched battery voltage.

The ECM controls the valve by operating the ground circuit, opening the purge valve at specific times allowing these gasses to enter the engine. The ECM monitors the ground circuit as well, watching for faults. When the purge solenoid isn't activated, the ECM should see a high voltage on the ground circuit. When the solenoid is activated, the ECM should see the ground voltage pulled low, close to zero. If the ECM doesn't see these expected voltages, or senses an open in the circuit, this code is set.

Potential Symptoms: P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) illumination. There may be no drivability problems at all. But, it's also possible to have a lean condition or a rough running engine if the purge valve is stuck open. Usually though, these symptoms are accompanied by other EVAP codes. Another symptom may be excessive pressure in the gas tank in the form of a "whooshing" sound when the cap is removed, indicating a purge valve that isn't working at all or stuck closed.

To cause a P0443, there has to be a problem with the purge control CIRCUIT, not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:
Bad purge solenoid (internal short or open)
Wiring harness chafing or rubbing another component causing short or open on control circuit
Connector worn, broken or shorted due to water intrusion
Driver circuit inside powertrain control module (PCM) is bad

Possible Solutions
1. Using a scan tool, command the purge solenoid to activate. Listen or feel for a clicking coming from the purge solenoid. It should click once, or on some models it may click repeatedly.

2. If it doesn't click with scan tool activation, unplug the connector and examing the solenoid and connector for damage, water, etc. Then check for battery voltage on the feed wire with the key on. If you have battery voltage, then ground the control side manually using a jumper wire and see if the valve clicks. If it does, then you know the solenoid is working properly but there is a problem with the control circuit. If it doesn't click when you manually ground it, replace the purge solenoid.

3. To check for a problem on the control circuit (if the solenoid tests okay and you have voltage to the solenoid) plug the solenoid back in and remove the control circuit (ground) wire from the ECM connector (If you're unsure how to do this, do not attempt). With the ground wire removed from the ECM, turn the key on and then manually ground the Purge valve control wire. The solenoid should click. If it does, then you know there is no problem with the control wire to the solenoid and there is a problem with the ECM purge solenoid driver circuit in the ECM. You'll need a new ECM. However if it doesn't click, then there must be an open in the wiring between the ECM and and the solenoid. You must find it and repair it.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 23, 2012 | Kia Sportage Cars & Trucks

1 Answer

Where is the evap purge canister valve located on a 2002 kia sedona?


The canister purge valve is located behind the intake manifold in the engine compartment on the firewall side .It should be a small round solenoid with a wire connector attached.It will have a feed hose from the evap cannister to the purge valve and then to the intake manifold.The evap canister is located on under the vehicle on the right side of the gas tank and is held in place by a bracket.If you follow these hoses it will also get you to the canister purge valve.I hope this helped.

Feb 03, 2011 | 2002 Kia Sedona

1 Answer

Cheq engine cod. p0440


EVAP emissions control malfunction. EVAP purge solenoid valve faulty.
Check the gas cap first. Try tightening your gas cap a few clicks or might have to buy a new gas cap.

And remember do not "top off" the gas tank when refueling. That seems to help not develop problems in the future.

Apr 02, 2010 | 2001 Kia Sportage

1 Answer

Were is the evap located on 2001 Chevy s-10 blazer with v6


The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.

47e8f38.jpg

Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve


4d7b3e9.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).

Mar 26, 2010 | 2001 Chevrolet Blazer

Not finding what you are looking for?

Open Questions:

See all 2001 Kia Sportage Questions

2001 Kia Sportage Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...