Question about Daewoo Leganza

Open Question

Daewoo espero Brake pedal goes all the way to the floor. Virtually no braking effect Have changed out master cylinder (using 2nd hand unit) and bled brakes- still the same problem. Am I missing somthing?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: 1998 chevy s10- brake pedal goes to the floor-

Did you put fresh fluid in the master cylinder? I really think you still have air in the lines. To bleed manually, start with the bleeder the greatest distance from the master cylinder, car running, helper pushing down about half way on brake pedal and releasing 3 times, on 3rd time, holding pedal down to half way depressed point while you open the bleeder valve. Repeat until you are sure all air has been flushed out. Check master cyl reservoir level often, because if it gets low and you **** air into the system, you have to start all over again. Go to wheel next greatest distance from master cyl, repeat above, working your way to wheel closest to master cyl last.

Posted on Apr 12, 2009

redbeard00
  • 957 Answers

SOURCE: just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes

Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Posted on Apr 29, 2009

  • 218 Answers

SOURCE: SOFT BRAKE PEDAL ON MY DAEWOO

MAKE SURE THE ARE NO OTHER LEAKS.IF U DID NOT BENCH BLEED THE MASTER CYLINDER BEFORE U PUT IT ON U PROBLEBLY HAVE AIR IN THE SYSTEM.BLEED THE MASTER CYLINDER AT THE LINES THAT COME OFF OF IT.THEN U NEED TO BLEED THE REAT OF THE BRAKES IN THIS ORDER.RIGHT REAR,LEFT FRONT,LEFT REAR.RIGHT FRONT.WHEN BLEEDING THE BRAKES WAIT 15 SECONDS BETWEEN PUMPS OF THE BRAKE PEDAL.IF U GO TO FAST U CAN DAMAGE THE MASTER CYLINDER.GOOD LUCK

Posted on May 01, 2009

emissionwiz
  • 75822 Answers

SOURCE: brake pedel pushes to the floor

pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Posted on Jun 27, 2009

emissionwiz
  • 75822 Answers

SOURCE: brake pedal dropping to floor

do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.

Posted on Oct 18, 2009

Testimonial: "Thank You"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Navara d22 brake pedal slowly goes to the floor only when engine is running I have changed master cylinder ,rear shoes,rear cylinders as they were leaking bled oil can you help


nissan vehicle have a problem in the bleeding of the brake and as a result pressure bleed is more effective that the normal method
Take the vehicle to an accredited brake shop and have the brakes pressure bled or have a proper diagnosis done to find the fault

Dec 14, 2016 | Nissan Navara Cars & Trucks

2 Answers

1994 Jeep Grand Cherokee brake pedal goes all the way to the floor. Recently replaced calipers and master cylinder and bled the whole system. Brake pedal goes all the way to the floor when first pushed...


Not bleed properly
or you have a rusted out line (leak)

There is NO Procedure-- that when driving a
vehicle or bleeding brakes,do you ever pump them

Dec 03, 2014 | 1994 Jeep Grand Cherokee

1 Answer

My 1998 ford taurus brake pedal goes straight to the floor .


Brake line busted somewhere? Is the linkage to the master cylinder intact? Master cylinder might have been installed incorrectly.

Dec 04, 2013 | Cars & Trucks

1 Answer

BRAKES BLED PEDAL GOES TO FLOOR WHEN STARTED


if a master cylinder is bad and you are sure you have all the air out and no leaks.pedal will go to floor , running or not. if booster is bad it will cause a hard pedal. but if master cylinder is bad it will turn on a brake light on dash if it works. make sure the wheel cylinders are not leaking. I beleive that the master cylinder is bad, or you have a leak somewhere. If the master cylinder is functioning properly, the brake pedal will depress to a certain depth and no further.

Apr 20, 2012 | 2000 Chevrolet Blazer

4 Answers

Brake pedal goes nearly to floor front pads, calipers, brake hoses changed, rotors turned Master cylinder changed, brake booster check valve changed rear brakes checked, drums good no ridge, shoe's...


I would go with not bled correctly

The booster should hold up with a hard pedal until
you start the engine, then vacuum causes it to move
down when pressing on the brake

Sep 16, 2011 | Saturn SC Cars & Trucks

1 Answer

I have bled brakes replaced front pads and even replaced rear passager wheel cylinder and re bled brakes still not working when car is running


Did you run out of brake fluid , if you did the brake master cylinder seal may have reversed and when you are trying to bleed the brakes the fluid is bypassing the seal , you think you have a good pedal when the engine is not running , but when you start the engine the pedal goes to the floor , you will need to fit a new or second hand master cylinder to cure the problem , I had this with my sons car and the problem was cured with a second hand master cylinder , I hope this helps

Sep 25, 2009 | Volkswagen Golf Cars & Trucks

3 Answers

Replace brakes. now they go to the floor. bled air


When you fixed the brakes, did you take the lid off the master cylinder. I just wonder if you spilled out your brake fluid. The only reason the pedal should go to the floor is if the brake fluid is gone or the master cylinder is not working. Check the fuse. Check the brake fluid level. The pedal only goes to the floor if there is no back pressure in the lines between the master cylinder the lines to the brake pistion on the calipers. Please give me a good ratin and keep me informed.

Jul 07, 2009 | 1999 Cadillac DeVille

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

1 Answer

SOFT BRAKE PEDAL ON MY DAEWOO


MAKE SURE THE ARE NO OTHER LEAKS.IF U DID NOT BENCH BLEED THE MASTER CYLINDER BEFORE U PUT IT ON U PROBLEBLY HAVE AIR IN THE SYSTEM.BLEED THE MASTER CYLINDER AT THE LINES THAT COME OFF OF IT.THEN U NEED TO BLEED THE REAT OF THE BRAKES IN THIS ORDER.RIGHT REAR,LEFT FRONT,LEFT REAR.RIGHT FRONT.WHEN BLEEDING THE BRAKES WAIT 15 SECONDS BETWEEN PUMPS OF THE BRAKE PEDAL.IF U GO TO FAST U CAN DAMAGE THE MASTER CYLINDER.GOOD LUCK

May 01, 2009 | Daewoo Leganza Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...