Question about 1992 Chrysler Imperial

Open Question

Installing belt tensioner on chrysler imperial

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: how to change serpintine belt on 93 chrysler imperial

Go to the follwing web site: http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

Enter the year,make,model and engine size of the car. Select to the left "Routing diagram" just under where it lists the part number for your serpentine belt.

Hope this answers your question. Best of luck.
Greg

Posted on May 29, 2009

moparownr
  • 667 Answers

SOURCE: how do I loosen the tension of the pully to

Look for the tensioner assembly, it will be the one pulley on an arm, look at that arm, there will be a square drive hole in the arm, you should be able to put a 3/8" drive ratchet or breaker bar in that hole, then pull it the opposite direction of the belt. If there is no hole then use a wrench that fits the nut in the center of the tensioner pulley and again pull in the opposite direction of the belt. Remember to look at the routing carefully for installing the new belt. Hope this helps, let me know

Posted on Dec 10, 2009

Testimonial: "there is no hole in the arm and I cant put a socket on the nut because of the clearance. I will try to find a long end wrench to put on it. Thank you"

  • 248 Answers

SOURCE: How to replace a serpentine

Locate the "belt-tensioner" Remove the old belt by pulling the belt-tensioner to remove the pressure on the belt. Reinstall a new belt. If needed, the belt pattern can be found on the frame next to your radiator (a sticker with a belt pattern)

Posted on Jan 09, 2011

clifford224
  • 1975 Answers

SOURCE: I can"t find a serpintine

This should be the right one for your car. 3.8 L. I hope this helps and good luck.

clifford224_11.jpg

Posted on Feb 17, 2011

  • 1168 Answers

SOURCE: What's the belt diagram for 92 Chrysler imperial

Hello.
Here you are as asked for.
Thank you for using FixYa.
kiltylake_233.gif

Posted on Mar 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fan belt broke I bought a new one but I don't know how it goes its a serpentine belt for 1992 Chrysler imperial 3.


Usually there is a diagram under your hood but in case the sticker is gone here is a diagram. This is for a 1992 Chrysler Imperial 3.3L V-6


63ec7de.jpg

Aug 16, 2015 | Chrysler Cars & Trucks

1 Answer

How do I replace the serpentine belt on a 1994 concorde?


Remove the alternator/power steering pump and water pump drive belt to gain access to the air conditioning drive belt.
To remove and install the air conditioning compressor drive belt, first loosen the tensioner pulley lock nut, then turn the adjusting screw to raise or lower the tensioner pulley assembly Accessory Drive - 3.3L Engine or Accessory Drive - 3.5L Engine To adjust the air conditioning drive belt, loosen the tensioner pulley nut and adjust belt tension by tightening adjusting screw. Torque pulley nut to 54 N•m (40 ft. lbs.) after adjustment.
The Poly-V generator/power steering belt has an adjustable tensioner pulley located on the timing belt cover Accessory Drive - 3.5L Engine to maintain proper belt tension. To remove or install this belt, Release tension by loosening the tensioner pulley nut and adjustment bolt Accessory Drive - 3.5L Engine Reverse procedure to install and tighten belt to specified tension.

Jul 10, 2012 | 1994 Chrysler Concorde

1 Answer

Need help installing serpentine belt on 1990 Chrysler Imperial 3.3 V6 with A/C. Space is limited for getting hands in to loosen belt tensioner or anywhere to get belt over pulley's. Any suggestion


Be sure to start by making sure you have the belt routing diagram or draw on up! I have trouble stuffing my hands into some of those spaces too. Usually what I do is locate the tensioner pulley and depress it. I've used long flat wrenches designed for exactly this problem all the way to a pry bar placed and used carefully so as not to damage anything. There is usually a flat (no grooves) pulley that you can slip the belt off of. Once you get it off a single pulley, gently release the tensioner and you can start to feed the belt off. Again, using a long screwdriver or whatever necessary to get it off. Then again, you could just cut it and pull! Feed the new belt in to the bottom and work up. Keep the belt snug so you don't knock one side off while trying to wrap it around another and work it up to the same pulley that you pulled it off from to start. Again, press the tensioner down, pop the belt in to place. INSPECT carefully to be sure nothing slid off a pulley even a little bit. Then you should be good to go! A pain for those of us who can't wear "one size fits all" gloves but its the best solution I've come up with! Best of luck!

Jan 21, 2012 | Cars & Trucks

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

1 Answer

Need a diagram for tensioner/idler pulley assembly for 92 chrysler new yorker 3.3L


Please let me know if you have any questions, and thanks for using FixYa.
3.3L AND 3.8L ENGINES-SERPENTINE BELT

See Figure 12
The Poly-V drive belt is provided with a dynamic tensioner to maintain proper belt tension. To remove or install this belt:
  1. Raise the front of the vehicle and safely support on jackstands.
  2. Remove the right front splash shield.
  3. Release tension of the belt by rotating the tensioner assembly clockwise.
  4. While holding the tensioner in the rotated position, remove the belt from the various pulleys-make sure to note the route that the belt takes before removal.
  5. To install the belt, route it through the various pulleys except for the tensioner pulley. Once the belt is satisfactorily mounted on the pulleys, rotate the tensioner clockwise and slide the belt onto the tensioner pulley. Make certain that the belt is mounted so that the grooves in the belt are correctly aligned with the grooves in the pulleys.
jturcotte_1511.gif

Fig. Fig. 12: To remove the serpentine belt from the 3.3L and 3.8L engines, rotate the tensioner assembly clockwise

  1. Install the right front splash shield to the underside of the vehicle.
  2. Lower the vehicle back to the ground.
  3. Start the engine and allow to idle for a few minutes. Shut the engine off and double check the placement of the belt on the pulleys.

Apr 09, 2011 | Chrysler New Yorker Cars & Trucks

2 Answers

What's the belt diagram for 92 Chrysler imperial


Hello.
Here you are as asked for.
Thank you for using FixYa.
kiltylake_233.gif

Mar 21, 2011 | 1992 Chrysler Imperial

1 Answer

How to replace a serpentine belt on a 91 chrysler imperial?


Locate the "belt-tensioner" Remove the old belt by pulling the belt-tensioner to remove the pressure on the belt. Reinstall a new belt. If needed, the belt pattern can be found on the frame next to your radiator (a sticker with a belt pattern)

Jan 09, 2011 | 1992 Chrysler Imperial

1 Answer

Ho is the power steering belt on 2002 chrysler


Click on the following direct Link. It has the Belt Diagrams you will need, complete with Removal Diagrams and Directions. It also has numerous other helpful diagrams for use.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/sebring/2002_chrysler_sebring_drive_belt_routing_diagram.htm

Mar 25, 2010 | 2002 Chrysler Sebring

1 Answer

Need diagram to install it belt for 1991 chrysler imperial 3.9 en


Try service manual here: http://www.manualslib.com/

Oct 12, 2009 | 1992 Chrysler Imperial

2 Answers

Where can i find a diagram to install serpentine


Most parts stores can print this out for you for free.

Sep 10, 2009 | 1991 Chrysler LeBaron

Not finding what you are looking for?
1992 Chrysler Imperial Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...