Question about 1997 Ford Expedition

1 Answer

?Internal lights on runner

I have a 99 Expedition, everytime
I turn car off in hit locks mt lights keeps coming on every 30 seconds until it drains battery.
What should
I do?









/

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    queens english please ,,,hits lock please explain a bit better

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 38 Answers

Hit all door latches (part on the door jam that holds the door closed) with a couple shots of WD-40, i found that it is the door sensor that gets gummed up. Worked immediatly for me.

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2009 elantra and when doors r locked and I hit the starter the car lights blink twice and doesn't start! It was a factory install by Hyundai . The car is an automatic . What do I do? Thanks


I would return it to the installer

My 2012 Hyundai Elantra Wont Start - CarGurus

www.cargurus.com > Questions > Hyundai > Elantra

CarGurusJul 30, 2013 - My 2012 hyundai Elantra GLS would not start this morning. ... I hit my door unlock on mt Key fab and the doors unlocked fromt here I proceeded start my car.... it and it wont turn over just makes a light click. not like a battery issue. .... But if Istart from the zero position on the starter it doesn't start on the first try ...

No horn / No lights when I lock my car - Hyundai Genesis ...

www.gencoupe.com/.../244433-no-horn-no-lights-when-i-lock-my-car.h...

Mar 30, 2014 - 16 posts - ‎8 authors
I do not know what could have caused this but when i lock my car... ... lock yourdoors with your key fob(might have to hit the lock button twice) ... The alarm/horn should start beeping. ... 2010 Hyundai Genesis Coupe 2.0T R-spec in Karussel White.... My lights flash when I lock it, but the horn doesn't sound.

2013 Hyundai Elantra Engine Won't Turnover, Won't Start ...

www.carcomplaints.com/.../Elantra/.../engine_wont_turnover_wont_start...
The 2013 Hyundai Elantra has 19 complaints for engine won't turnover, won't ...

Jan 04, 2016 | Hyundai Cars & Trucks

1 Answer

2005 ford 500, won't start a lock light is


need to reprogram ignition key security system when battery disconnected. turn ignition key to the on position for 3 to 10 seconds until the lock light goes out then start vechicle.if lock light dont turn off turn ignition switch to on position 30 seconds until lock light turn off.

Jun 12, 2013 | Cars & Trucks

1 Answer

My battery is just a week old ...


if problem started after you replaced battery you baught a bad battery it happens.

Jan 04, 2010 | 2000 Ford Expedition

1 Answer

99 ford expedition, abs light stays on, front brakes seem to be dragging


When was the last time you changed the front brake pads?
Try this:
Keep the brake pedal pressed down and start the car, after it idles for about 10 second let go of the pedal. If the light comes on just as you leave the pedal - try pumping it a few times, turn the car off and pump the pedal some more until it becomes real hard.
Then, keeping your foot to the pedal, start the car.
Idle for about 10 seconds, let go of the pedal and press it again rel fast.
If the light doesnt come on again - it means you have a leak of some sort or that the main brake pump should be replaced.

Good luck.

Jul 11, 2009 | 1999 Ford Expedition

1 Answer

How to program 1997 Maxima remote


Try this it works for the 95 and 96 models it should also work for all models 95 thru 99. 1st you need to get in the car and hit the lock button on the drivers door switch. Make sure doors and windows are all shut. To program the remote you must insert the key into the ignition 6 to 8 times rapidly in a 10 second time period and when you have done it correct the hazards lights will then illuminate twice. Next then you must hit the lock button quickly on the remote due to a slight time delay only hit the button once. Keep repeating this step until it works and to find out if it worked hold down the trunk button or the unlock button(the front windows should let down on you Mad-Max.

May 24, 2009 | 1997 Nissan Maxima

4 Answers

MY 99 XK8 CONVERTIBLE WINDOWS GO DOWN 1/4 '' EVERYTIME YOU OPN THE DOOR BUT NOT WILL GO UP AUTOMATICALLY,AS DESIGNED TO DO.HOWEVER THEY WILL GO UP IF YOU RAISE THEM WITH THE SWITCH INSIDE THE CAR,BOTH...


It just needs resetting.Hold each window switch down until you hear a click at the top and then go down all the way and hold until it clicks at the bottom of its travel.A low battery will cause this sometimes or a  battery change.Tony/Hills Motors, San Mateo, CA

May 02, 2009 | 1999 Jaguar XK8

1 Answer

Programing a new remote


Use these instuctions if your Deville has an Analog Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Panel (CCP) simultaneously.
(Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.

If “RFA DATA” is displayed, press FAN DOWN.
If “RFA OVERRIDE” is displayed, press FAN UP.
2. If “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
If “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.
3. IPC will show “0” on right side of Driver Information Center (DIC) display.
Press warmer button on climate control unit until “99” is displayed.
4. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.

5. To program a second remote, press FAN DOWN button until “RFA 502 PROGRAM FOB #2” is displayed, then press
FAN UP. Repeat step 4.

To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.




Use these instructions if your DeVille has a Digital Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
light all telltales, go blank then enter DIAGNOSTIC
MODE. Press FAN DOW button to scroll through system until
“RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
press FAN UP button. When “NO OVRD RF 500” is displayed, then press FAN UP button.

2. When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
below odometer. System is now ready to program remote.

3. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.)

4. To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
program second remote.

To exit system, press RECIRC or RESET buttons.

Disclaimer

Apr 25, 2009 | 1998 Cadillac DeVille

2 Answers

Electical problems with 99 ford expedition


check your interior fuse panel. does it look wet or corroded? is there a water leak maybe from the the window if you have a sun roof the drain could be leaking into the car. or it could just be a problem with a module or a corroded ground or other conection.

Mar 16, 2009 | 1999 Ford Expedition

1 Answer

Programing a remote on a 99 quest


first make sure,that the batter is ok. You will need to have both remotes while doing this.
1: get in and lock the doors with the power door lock
2: insert the key into the ignitoin repeatedly IN and OUT 6 times in a row or just keep doing so, until the hazard flashers flash on the dash board (observe the dash board while inserting key)
3: after the hazadrs flash TURN key into the ACC position/not start.(dash will light up) DO NOT START
4: with the key in ACC position, hit lock button on the remote. That will program that remote.
5: to program the other remote simply unlock the door with the door lock switch and relock it with the swithc and hit the other remote button.
6: done

Sep 16, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
1997 Ford Expedition Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...