Question about 2004 Infiniti G35 Sport Coupe

1 Answer

Need assistance with changing Drive belts - help!

I am changing 2 old drive belts, how do i release them from the pulleys?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Infiniti Master
  • 21,949 Answers

Look for the adjusters

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changing serpentine belt on 2004 dodge ram 1500


What are you asking for ? Attached find a link with serpentine installation for your motor vehicle

5.7L ENGINE


8199c656.gif
1 - A/C COMPRESSOR OR IDLER PULLEY 2 - FAN DRIVE PULLEY 3 - POWER STEERING PUMP 4 - CRANKSHAFT PULLEY 5 - IDLER ASSEMBLY 6 - TENSIONER ASSEMBLY 7 - ACCESSORY DRIVE BELT 8 - GENERATOR 9 - IDLER PULLEY
  1. Remove the air intake tube between intake manifold and air filter assembly.
  2. Insert a suitable square drive ratchet into the square hole on belt tensioner arm.
  3. Release the belt tension by rotating the tensioner clockwise. Rotate belt tensioner until belt can be removed from pulleys.
  4. Remove belt.
  5. Gently release tensioner.

May 30, 2014 | Cars & Trucks

1 Answer

How to change the water pump on a 2006 equinox ls


  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Loosen the water pump pulley bolts.
  3. Rotate the drive belt tensioner to release the tension on the drive belt.
  4. Remove the drive belt from the right idler pulley.
  5. Carefully release the drive belt tensioner spring tension.
  6. Remove the water pump pulley bolts.
  7. Remove the water pump pulley.
  8. Remove the water pump bolts.
  9. Remove the water pump.
  10. Remove the water pump gasket.
  11. Clean the water pump mating surfaces.

To install:

Fig. Remove the mounting bolts (3) to remove the water pump (1) and gasket (2).
  1. Install the water pump gasket (2).
  2. Install the water pump (1).
  3. Install the water pump bolts (3). Tighten the bolts to 10 Nm (89 inch lbs.).
  4. Install the water pump pulley. Loosely install the pulley bolts.
  5. Insure the drive belt is properly centered on all the pulleys except the right idler puller.
  6. Rotate the drive belt tensioner away from the drive belt.
  7. Install the drive belt to the right idler pulley.
  8. Release the tensioner allowing the drive belt tensioner to come in contact with the drive belt.
  9. Inspect the drive belt to insure the belt is properly centered on all the pulleys.
  10. Tighten the water pump pulley bolts. Tighten the bolts to 25 Nm (18 ft. lbs.).
  11. Fill the cooling system.
  12. Inspect the cooling system for leaks.


10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-0.jpg

10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-1.gif

Aug 21, 2011 | 2006 Chevrolet Equinox

1 Answer

Passat 1998,4cylinders, turbo, what is the belt routing diagram, the power steeling belt is related with the water pump or not, thank you


The ancillary belts routing diagram for a 1998 VW Passat 1.8 Turbo

tdisline_822.jpg
AC = Air Conditioning
CS = Crankshaft
F = Fan pulley
G = Generator
PAS = Power Assisted Steering
T = Tensioner pulley
WP = Water Pump

1. Viscous coupling removal (lock the viscous coupling).

tdisline_823.jpg

2. Lock the ancillary drive belt tensioner.

tdisline_825.jpg

3. Lock the coolant pump.

tdisline_826.jpg
4. Remove the coolant pump drive belt.
5. Remove the ancillary drive belt.
6. Release the A/C tensioner if vehicle is equipped with A/C (Air Conditioning).
7. Remove the A/C compressor drive belt.

Aug 09, 2011 | 2004 Volkswagen Passat

1 Answer

How do I get a diagram to show me how to put a serpentine belt on a 1998 Ford Escort Station Wagon?


you ask here. Please rate highly

SECTION 303-05: Accessory Drive 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Belt -2.0L SPI Removal
  1. Relieve the drive belt (8620) tension.
    • Use a (A) ratchet or breaker bar inserted in the square hole in the drive belt tensioner flange.
    • Rotate the (B) drive belt tensioner (6B209) in a clockwise motion to release belt tension.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the engine splash shield.
  1. Remove the drive belt from the accessory drive belt routing pulley (6C348) and then the remaining accessory pulleys.
Installation
  1. Position the drive belt over the accessory pulleys. Raise and support the vehicle if necessary; refer to Section 100-02 .
  1. Install the engine splash shield.
  1. Rotate the drive belt tensioner in a clockwise motion.
  1. Slip the drive belt under the belt idler pulley (8678) and release the tool. Remove the tool from the drive belt tensioner.
  1. Accessory Drive-With A/C
  1. Accessory Drive-Without A/C
snorkelbobby_74.gif
---------------------------------------------------------------------------------------------------
Belt -2.0L Zetec Removal
  1. Raise the vehicle on a hoist; refer to Section 100-02 .
  1. Use a 13 mm wrench to rotate the drive belt tensioner (6B209) in a clockwise motion.
  1. Remove the drive belt (8620).
Installation
  1. Position the drive belt on all the pulleys and the drive belt tensioner.



Item Part Number Description 1 10300 Generator 2 19A216 Drive Belt Idler Pulley 3 3D673 Power Steering Pump Pulley 4 8509 Water Pump Pulley 5 6B209 Drive Belt Tensioner 6 19703 A/C Compressor 7 6316 Crankshaft 8 19A216 Drive Belt Idler Pulley 9 8620 Accessory Drive Belt
  1. Rotate the drive belt tensioner in a clockwise motion.
  1. Install the drive belt and gently release the drive belt tensioner.
    • Run the engine for several minutes to seat the belt into the pulley grooves.


snorkelbobby_75.gif

Jul 09, 2011 | Ford Escort Cars & Trucks

1 Answer

I need a routing diagram for a 2007 dodge caliber alternator


aaronsnipes.jpg



1. Install the accessory drive belt (2) around all the pulleys except for the generator pulley (3). 2. Using a wrench, rotate accessory drive belt tensioner (8) counterclockwise until accessory drive belt (2) can be installed on the generator pulley (3). Release spring tension onto accessory drive belt (2).

Mar 07, 2011 | Dodge Caliber Cars & Trucks

4 Answers

How to remove alternator on a 2005 range rover


Hi
Click here

the link above should tell you all you need to know if you get stuck or have any problems give me a shout back ok

Oct 26, 2010 | Land Rover Range Rover Cars & Trucks

2 Answers

Diagramm serpantine belt 2005 sprinter2500


Hi.

Here the belt routing for 2005 Dodge Sprinter 2005, whch was sold only with the 2.7 engine mounted:



feac688.jpg


Fig. Accessory Belt Routing-A/C Compressor (1), Power Steering Pump (2), Tensioner (3), Crankshaft Pulley (4), Water Pump (5), Alternator (6), Idler Pulley (7)-All Engines

Here a different view:

62bcecc.jpg

Here also the fan belt routing;

729c6e0.jpg

Fig. Fan belt routing-Fan pulley (1), Fan belt (2), Crankshaft pulley (3)-3.0L engine shown

PROCEDURE Removal & Installation


2.7L Engine

1. Loosen the tension adjust and remove the A/C compressor drive belt.
2. Attach a 3 / 8 inch drive ratchet to the automatic belt tensioner.
3. Rotate the belt tensioner counterclockwise to release the belt tension.
4. Remove the accessory drive belt, starting with the water pump pulley.



To install:

1. Position the accessory drive belt around every pulley except the water pump pulley.
2. Rotate the drive belt tensioner clockwise, install the accessory drive belt and release the tensioner.
3. Position the A/C Compressor drive belt over the crankshaft pulley and A/C compressor pulley.
4. Tighten the drive belt tensioner.
5. Ensure the belt is seated properly on all of the pulleys.

If this solution was helpful, then please do not forget to Accept.
Writing dedicate solution, sharing skills, researching and extracting info from service documents takes time, and your feedback is important for us.
If you repute any solution useful, please click on Accept.

All the best.

Ginko.

Sep 21, 2010 | Dodge Sprinter Cars & Trucks

1 Answer

Timing belt replacement


hello,




The solution provided below will be of great assistance to you;


1.Ensure to Study the exact path that the drive belt follows across the pulleys and make sure you know it

2.Loosen the drive belt tensioner by loosening its upper locking nut with a wrench, then slip the drive belt off the crankshaft pulley first and remove it from the others.

3.Take the old drive belt with you to the auto parts shop so it can help you to get the correct length, width and design for the replacement belt.



4.Install the replacement drive belt onto the pulleys, making sure it runs in the same path as the old one. Check and make sure the belt fits properly in each of the ribbed grooves within the pulleys.



5.Adjust the drive belt tensioner until it gives the belt the proper tension and tighten the locking nut. On some engine types. the belt uses a dynamic tensioner that will automatically set and maintain the correct tension.






Thank you...

Sep 06, 2010 | 2001 Dodge Caravan

3 Answers

My 1998 Windstar with the 3.0L engine needs an alternator. Easy enough fix except I don't know how to work with the serpentine belt (all my other vehicles are old skool). Where is the tensioner and how do...


Removal
  1. ani_caut.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.
    Using a 15 mm socket or wrench attached on drive belt tensioner pulley bolt. Rotate drive belt tensioner (6B209) clockwise to remove drive belt from pulleys.


    Pulley Routing, Accessory Drive Belt—3.0L Engine

30d485d.gif
Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 6B217 Drive Belt Tensioner Pulley 4 6B209 Drive Belt Tensioner 5 3A733 Power Steering Pump Pulley 6 19703 A/C Compressor 7 6312 Crankshaft Pulley 8 8509 Water Pump Pulley

Installation
  1. Install drive belt over all accessory pulleys (except drive belt tensioner ).
  1. Rotate drive belt tensioner as described under Removal to install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys.

Feb 28, 2010 | Ford Windstar Cars & Trucks

1 Answer

How do I change the pulley on my 01 sante fe v6? I know it has an automatic tensioner but I don't know how to take the serp belt off to change the pulley.


Tell you what... No response, then I can't help. If you're talking about the accessory drive belt tensioner pully, there are two 12mm bolts which mount it to the engine. You'll need a 3/8's drive ratchet (or other 3/8's drive device) to release the tension so you can remove the accy drive belt to facilitate removal of the tensioner pully. Once you're remove the accy drive belt, remove the two (2) 12mm bolts holding the tensioner pully to the engine (make visual note of position/direction of the drive belt when you do this because you'll need to position the drive belt in the same orientation when you install a new auto-tensioner in place of the old one.).

May 13, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13160 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...