Question about Hyundai Cars & Trucks

Open Question

How to drop fuel tank to replace 1994 hyundai scoupe fuel pump

Can fuel tank straps be unbolted to lower tank to access fuel pump without removing tank from car

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 1994 Toyota Truck 22R Engine

Saw your post on another thread. I have the same truck. The fuel filter is located on the rail just below the passenger door. Its an easy one to remove,...couple bolts, but access to it is a pain.

Posted on Aug 11, 2008

Ad
StormStrikes
  • 104 Answers

SOURCE: 2000 PONTIAC FIREBIRD FUEL PUMP REPLACEMENT

Many of the Pontiacs of that era up to even present models had an access panel in the trunk that you could access through the back seat pass through.

Its been a while since I seen the inside of a Firebird, but in thinking about it the back seat pass through may not be present on the Firebird, but it may be worth the time to lift up the carpeting in the trunk area and see if there is an access panel to the fuel pump.

Posted on Dec 30, 2008

  • 6982 Answers

SOURCE: Fuel filter replacement

I supose that the lines could be left on, however they will really get in your way when working. If they require a "tool" to remove them, get one. Make sure that the tank is near empty before taking it down... gasoline weighs about 7.5lbs per gallon. It can be very heavy!!!

Posted on Jan 02, 2009

  • 1 Answer

SOURCE: fuel pump - 2003 Pontiac Grand Am

2003 Grand Am GT,You have to drop the fuel tank,remove heat shield,remove all lines,electrical plug ins,then you are ready to do straps,be sure to go get extra nut and bolts for straps (2) of them had to cut off old ones,once straps are off depending on how much gas is in the tank used jack to lower tank,fuel pump was a twist off with locking mechanisms on top of tank,used a rubber malet and screw driver to loosen,pull out after diconnecting plug ins etc,replace blue plug in for harness to fit new pump,was recommended since it could corrode,lifted tank back up connected wires,lines etc,put key in on position 3-4 times for pump to pump,car started 1st time,my first fuel pump took my son and I 2 1/2 hours,new pump $250.00 wire harness $15.00 and two new nuts and bolts $3.25

Posted on Mar 13, 2009

batviper
  • 120 Answers

SOURCE: How to Replace a Fuel Pump in a 1990 Acura Integra

the fuel pump should be in the canaster the float is in

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 94 Dodge Ram 1500 4x4 5.9L With a bad fuel pump. What I would like to know is how to release the fuel pressure in the line before removing the fuel pump. Also do I have to drop the fuel tank to...


Well I released my pressure by pushing in the valve near the injectors under the hood. Make sure your engine is cold when doing this. Only a quick spray then its relieved. I unbolted my bed and jacked it about 5 inches and was able to change my 94 ram fuel pump. Pretty easy this way as those straps may need to be eplaced if removed. I did this 2 years ago. Maybe to an hour or 2. But if your truck has been sitting yow may want to drop the tank to clean it out.

May 01, 2013 | 1994 Dodge Ram

3 Answers

How do you replace a fuel pump on 1994 jeep grand cherokee


Disconnect the battery, Jack the rear up on stable jack stands. use a smaller jack with a piece of wood to stable the load under the tank. You will see 2 band straps under the tank, remove the bolts, only 1 side have bolts, the other side swings down. The hose from the gas cap will have to be disconnected, which can be !!!!! when in-stalling. you can then drop the gas tank down easily with the jack just a bit, enough to reach around to unplug the fuel pump plug, and the gas lines. Once it's removed, the pump has a big screw on ring, take it off and the fuel pump can be pulled out.

Apr 26, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How do you replace the fuel pump on a 1994 Mercury Sable Wagon ?


The fuel tank needs to be removed to replace the pump. Remove fuel from tank. The fuel filler and vent hoses need to be disconnected. The electrical connector needs to be disconnected. Unbolt tank straps(2). Lower tank down. Remove fuel lines from pump. Use a brass drift(to prevent sparks) and hammer to turn retaining ring that holds pump in tank. Install new pump with new "o" ring seal and reassemble in reverse order

Apr 01, 2010 | 1994 Mercury Sable

2 Answers

Need to change fuel pump for 99 chevy blazer how do i do it and where is the fuel pump located


first you need to relive the fule system of pressure. do this by finding your fule pump relay disconecting it and start the car. it will sputer, this is reliveing fule pressure.once it stops sputering your ready to get the fule pump out. it is located in the fule tank. the tank is held on by 2 straps your going to have to take off. once you do that drop the tank and the pump will be on top of it.

Feb 20, 2010 | 1999 Chevrolet Blazer

1 Answer

How to change fuel pump on 94 Plymouth voyager


you will have to lower fuel tank
fuel pump is on top of tank
disconnect all rubber hoses and electrical
unbolt straps
dispose of fuel carfully
be careful of fuel vapor, work in a ventilated area

Feb 20, 2010 | 1994 Plymouth Voyager

3 Answers

Need to know how to replace fuel pump on 2002 Pontiac Grand Prix 3.8 v6


You don't need to drop the tank to replace the fuel pump.
Under the carpet in the trunk there is a access cover that you can take off to access the pump. You need a good snap ring pliers to get the snap ring off to release the pump from the tank.
I wish people would have first hand knowledge of the process before they start clicking post and cost a person a lot of money and time for something that isn't needed to be done to complete the job.

Oct 10, 2009 | Pontiac Grand Prix Cars & Trucks

1 Answer

Replace fuel pump 2002 GMC Sierra


I don't think there is enought slack to drop the tank without unhooking the lines. You can take this advise if you want or not its up to you, but i always found it easier to unbolt the bed and lift it back about a foot and i could get right at the sender where the pump is and in some cases i dident even have to unhook the fuel lines, pull the sending unit out chg. the pump and put it back together. Or you can do it the other way, unhook the lines, electrical wires, filler hose, and straps, if its got gas in it better have some help 8# a gal. adds up.

May 26, 2009 | 2002 GMC Sierra 1500

1 Answer

In-the-tank fuel pump r&r


Here are instructions for replacment with a diagram of the fuel pump components my only suggestion would be instead of draining the tank and dropping the fuel tank if you unbolt the box and using a jack and and some wood lift the fuel tank side of the box this will give you access to the tank and fuel pump/ sending unit. It will save you time and the hastle of replacing the tank straps which are prone to snapping at the threads when trying to remove the nuts.If these brake you will have to replace them.

Nov 16, 2008 | 1994 GMC Sierra

2 Answers

Trying to replace fuel pump


two straps ..and the filler neck still needs disassembled...remove wires at top of tank before dropping all the way(including any ground strap)

Oct 25, 2008 | 1996 Pontiac Firebird

3 Answers

1994 Toyota Truck 22R Engine (ext.cab,4x4,5 speed man.) Is it best to remove the truck bed or lower the fuel tank in order to replace the fuel pump? 1994 Toyota Truck 22R Engine


If you're doing it by yourself, drop the fuel tank.
Make sure it's almost out of gas first.

If you pull the bed, it's the bolts that hold the bed in, the wiring to the tail lights, and the tank filler neck to take loose. Then you have to pick up the bed of the pickup (a couple hundred pounds).
To get the tank out, it's the filler neck, and unbolt the straps that hold it in. Depending on how much fuel is in it, is how much it's going to weigh.
But as you loosen the straps, you can use a floor jack to hold the tank up. Same when putting it back in.

So I would go with taking the tank out, and not pulling the bed off.

Aug 01, 2008 | 1994 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...