Question about 1989 Jeep Wrangler

Open Question

How do i replace license plate bulb on 2012 jeep wrangler

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 3rd brake light won't work. Replace bulb...nothing

The contacts for the third brake light are two silver discs, about the size of a dime. They are located on the inside of the tailgate, hinge side. Make sure your carpet or any other loose item has not covered one or both contacts. Make sure they are fairly clean and make good contact.

Posted on Nov 30, 2008

Ad
ZJLimited
  • 17970 Answers

SOURCE: Jeep grand cherakee 1998 License plate lights not working.

Check this documents:
- ZJ-Secc-8L-Lamps (page 7, fig. 10)
- ZJ-Secc-8W-Wiring-Diagrams (rear lamps / page 139 and next, Diagram ZJ 98 and next)

Good luck (rated this help)


Posted on Aug 27, 2009

  • 2926 Answers

SOURCE: Back up lights and license plate light doesn't work.

Reverse lights are activated by a small switch on the transmission. Usually located on the passenger side of the vehicle with a small rubber cap over the switch, Your plate light bulbs are probably in need of replacement, and have nothing to do with the reverse lights.

Posted on Jan 17, 2010

  • 10 Answers

SOURCE: How to replace fog light bulb on an '03 Jeep

There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plate light does not work, but lights are good and sockets seem good


check bulb the number plate light runs on the same circuit as the side lights so if they are working its got to be a bad earth on the plate light

Jan 24, 2016 | Cars & Trucks

1 Answer

Which fuse goes to tag lights on 98 ford explorer


Which fuse belong to license plate light or which number ...

www.fixya.com/cars/t10801433-fuse_belong_license_plate_light_or
Nov 11, 2011 - The licence plate lights are in the same line as your tail light wiring assembly. I assume your ... Previous owner cut wires going to lights for license plate. ... 1996 ford explorer license plate fuse ... 09@1998 ford f150 fuse box.

1997 Ford license plate lights are not working. - Ford Explorer ...

www.explorerforum.com > ... > Performance Lighting

Mar 13, 2011 - 5 posts - ‎4 authors
can anyone tell me why my lights would not be working on my license plate, i replaced old bulbs with new bulbs and checked every fuse and ... Parking lights stay on
19 posts
Sep 5, 2012
my tail lights wont work, and im out of ideas. i need help ...
18 posts
Sep 15, 2011
License Plate Lights
11 posts
Mar 24, 2011
trailer light problem
15 posts
Apr 22, 2009
More results from www.explorerforum.com

Dec 10, 2015 | Ford Cars & Trucks

1 Answer

Replace license plate light


what country? ( export below means , NOT USA)
its in the FSM
quote:
A single standard equipment rear license plate lamp unit is integral to the
license plate mounting bracket just below the left rear lamp unit on vehicles manufactured for domestic
markets. A bracket with two rear license plate lamps is located on the rear bumper directly below the
spare tire on vehicles manufactured for export markets.
and HOW TO: quote
1. Disconnect and isolate the battery negative cable.
2. Remove the license plate from the rear license plate bracket.
3. Remove the four screws (4) that secure the rear license plate bracket and lamp unit (3) to the four spring
nuts (2) in the rear body sheet metal (5).
4. Pull the bracket and lamp unit away from the rear body sheet metal far enough to access and disconnect
the body wire harness connector (1) from the connector on the back of the bracket and lamp unit housing.
5. Remove the bracket and lamp unit from the vehicle.
unquote the FSM.
Buy one for $20-

Aug 19, 2013 | 2010 Jeep Wrangler

1 Answer

Trying to figure out how to pull this piece apart for replacement of rear license plate holder on my jeep wrangler yr 2012


If there is a latch on the connector, use a screwdriver to gently pry up the latch, then pull the two pieces of the connector apart

May 11, 2013 | Cars & Trucks

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

How do I replace a rear license plate bulb in 2004 Jeep Liberty?


  1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
  2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
  3. Remove the license plate lamp assembly from the rear bumper fascia.

Apr 16, 2011 | 2004 Jeep Liberty

1 Answer

How do you change the rear license plate light bulbs???


First look under when your license plate lights are and you will see 2 phllips headed screws remove those screws and the license plate light assembly will drop out of the bottom of the trunk, simply twist the blub to unlock it from the light housing pull the bulb straight out of the socket replace it with a new bulb and the installation is the reverse of the removal.

Dec 06, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Back up lights and license plate light doesn't work.


Reverse lights are activated by a small switch on the transmission. Usually located on the passenger side of the vehicle with a small rubber cap over the switch, Your plate light bulbs are probably in need of replacement, and have nothing to do with the reverse lights.

Jan 17, 2010 | 1996 Jeep Grand Cherokee

2 Answers

License plate being pulled up


decorative [and possibly functional] license plate frames are available after-market from companies like www.jcwhitney.com. a local machine shop or welder could fabricate a 'backing plate' to reinforce the plate.

Oct 15, 2009 | 1989 Jeep Wrangler

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...