Question about 2002 Ford Super Duty F 450

Open Question

How to reset air cleaner light on ford f-450 - 2002 Ford Super Duty F 450

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wracefans24
  • 1985 Answers

SOURCE: how to reset service soon light 2000 ford 450

The computer should have turned the light out if you installed a new sensor,unless you still have a faulty sensor,You need to have it put on a drb to check for current codes.

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the relay fuel pump for a ford f250 1988 450.


left side - drivers - beside the air cleaner towards the fire wall and I reaserch it on www.answers.com so you can go to that site and research anything you need to know

May 13, 2015 | Ford Cars & Trucks

1 Answer

Engine idles rough, I have new plugs, wires, air cleaner. Could it be air sensor and where would it be on 1998 Ford Explorer, 6cyl. .. Egine light stays on. I have tried to reset it, but it eventually...


what code are you getting when you check the obd2 computer usually the problem when an ford engine runs ruff check the tps sensor which is on the side of the throttle body opposite of the throttle cables tps stands for (throttle possitioning sensor)

Jul 08, 2010 | 1998 Ford Explorer

1 Answer

I have a 99 F-450 truck with a 6.8 motor. It just recently failed inspection for emissions, was told I need to change coil packs but there is no check engine light on, what do I look for?


it may have a dirty mass air flow sensor (MAF) and could couse a rich condition that would fail emissions test. it should throw a code but not always its a pretty delicate sensor and the contaminant may not b visible if u put an oil filter on it(K&N) if i use too much spray the sensor will malfuntion as it gets coated with oil. Gently remove the MAF from housing and spray the two sensor forks with carb n choke cleaner to remove contaminents.

Mar 16, 2010 | 2008 Ford F-350

1 Answer

How to reset service soon light 2000 ford 450


The computer should have turned the light out if you installed a new sensor,unless you still have a faulty sensor,You need to have it put on a drb to check for current codes.

Nov 18, 2009 | 2001 Ford Super Duty F 450

1 Answer

Reset ABS light on 2000 Ford F700 after repairing bad left rear sensor


dis-connect the battery terminals for 2 minutes and put it back on...

Sep 29, 2009 | 2001 Ford Super Duty F 450

2 Answers

A light that looks like a tire, but has arrow thru it


this is the engine air filter light according to my owners manual

Aug 01, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Code po171 7 po174


your computer is reporting bank 1 and 2 too lean, usually caused by the mass air flow (MAF) sensor, you can usually clean this sensor and reset the light. Clean it with electric cleaner or brake cleaner, make sure it is dry before reinstalling, also take care not to damage it. Hope this helps, let me know

Jun 09, 2009 | 1997 Ford Thunderbird LX

1 Answer

When I start up my car, it is jerking alot. It feels like it is going to stall. After about 5 minutes it stops.


Try cleaning the MAF sensor. Remove the sensor and clean it with a good electrical cleaner or MAF cleaner then let it air dry or use light shop air.Then do a couple of wide open throttle burst to reset the baro and should take care of it.

Mar 01, 2009 | 2001 Ford Mustang

1 Answer

My2001cobra with 38000 miles has gotten where it wont run properly until it gets hot it bucks and jumps until the heat is way up --any ideas


Clean the MAF sensor with some electrical cleaner or a MAF cleaner then let it totally dry or dry it with light shop air. Then do a couple of wide open throttle burst to reset the BARO reading and it should take car of it.

Feb 17, 2009 | 1997 Ford Mustang Cobra

1 Answer

Lighting problem


Have you checked the fuses and dimmer switch? Check the trailers bulbs there is usually one bulb with two filaments for each light, one filament can burn out without causing the other to go. If the bulbs are good you should start at the trailer light connector ( use a test light or voltmeter to test for power at the trucks wire harness first to see if it's the truck or the trailer ) and work your way back to the lights. Clean the contacts on the connector, bulbs and bulb sockets (steel wool and or a can of aerosol electrical contact cleaner).

Feb 07, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...