Question about 2004 GMC Sierra 2500
Could it be just a fuse or is there more to it? Like a part or even more?? heates seats not working and both power seats are not working. are they on the same fuse?
Very possible that they share the same fuse, and if it is a fuse, its easy to fix. Look in your owners manual and find the location of the fuse box, then simply replace the bad fuse with a new one of the same amperage.
Posted on Mar 03, 2009
I will post it in 2 different posts because its too long DB
HEATED SEAT SYSTEM
Individually controlled driver and passenger side electrically heated front seats are available factoryinstalled optional equipment on this model, when it is also equipped with the power seat option. The heated seat system allows both the driver and the front seat passenger the option to select one of two seat heating ranges, Low or High, or to turn the individual seat heaters OFF using the heated seat switches located in the center lower bezel near the bottom of the instrument panel center stack. The heated seat switch circuit operates on ignition switched battery current supplied through a fuse in the junction block, only when the ignition switch is in the ON position.
The heated seat system consists of the following components
The electronic modules that may affect heated seat system operation are as follows:
The heated seat system will only operate when the ignition switch is in the ON position, and the surface temperature at the front seat heating element sensors is below the designed temperature set points of the system. The heated seat system will not operate in ambient temperatures greater than about 41 °C (105 °F) . The front seat heating elements and sensors are hard wired to the Heated Seat Module (HSM) or the Memory Heated Seat Module (MHSM).
The heated seat switches are hard wired to the Body Control Module (BCM). The BCM monitors the heated seat switch inputs, then sends heated seat switch status messages to the HSM or MHSM over the Programmable Communications Interface (PCI) data bus. The HSM or MHSM contains the control logic for the heated seat system. The HSM or MHSM responds to the heated seat switch status messages, ignition switch status messages, and the front seat heating element sensor inputs by controlling the output to the front seat heating elements through integral solid-state relays.
When a seat heater is turned ON, the sensor located on the seat cushion electric heater element provides the HSM or MHSM with an input indicating the surface temperature of the seat cushion. If the surface temperature input is below the temperature set point for the selected Low or High heated seat switch position, the HSM or MHSM energizes the integral solid-state relay, which supplies battery current to the heating elements in the seat cushion and back. When the sensor input indicates the correct temperature set point has been achieved, the HSM or MHSM de-energizes the solid-state relay. The HSM or MHSM will continue to cycle the solid-state relay as needed to maintain the temperature set point.
The HSM or MHSM and the seat heater elements operate on non-switched battery current supplied through the power seat circuit breaker in the junction block. However, the HSM or MHSM will automatically turn OFF the heating elements if it detects an open or short in the sensor circuit, a short or open in the heating element circuit causing an excessive current draw, or when the ignition switch is turned to the OFF position.
See the owner's manual in the vehicle glove box for more information on the features, use and operation of the heated seat system.
I WILL POST THE REST
Posted on Feb 03, 2009
This is not un- common. The heating elements do wear after a while. It is probably an open circuit in one of the pads in your seat. A quick restance check can determine which one it is.
Posted on Jan 24, 2009
Remove fuses 10 and 11 in the underhood junction box. Leave out for 5 minutes then reinstall. If the seats start working your Zephyrs dual climate control seat module will need replaced.
Posted on Jul 03, 2009
No fuse.These seats are protected with relays and a seat module.The module is under the drivers seat.There are 3 connectors and it would be hard to check all these wires for power to the motors.First look under the seat and make sure none of the connectors came apart under the seat by something that might have been left or rolled under it.The 2 main ones you can check are the connector 2 terminal C and connector 3 terminal A.C is a black wire which is ground and A is a red wire which is the feed power wire.Connector 2 is green and 3 is black.If the ground and power wires are good then you could have a bad drivers seat module.What I would do is go to the salvage yard and find a used module to try.Good luck.
Posted on Dec 07, 2009
Testimonial: "Thanks for your assistance. Great information"
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Apr 01, 2014 | 2000 GMC Jimmy
Jan 25, 2013 | 2009 Lincoln MKS
Dec 18, 2010 | 2002 Oldsmobile Bravada
Apr 24, 2010 | 2004 GMC Yukon
Jan 17, 2010 | 2003 Chevrolet Tahoe
Nov 01, 2009 | 2004 Cadillac SRX
Apr 23, 2009 | 2006 Lincoln Zephyr
Jan 10, 2009 | 2004 GMC Sierra 2500
228 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: