Question about 1991 Toyota Pickup

Open Question

1989 Hilux ignition wiring diagram

Any chance of an ignition wiring diagram for a 4WD Hilux with a 3Y engine, ( ignition coil, igniter and pulse coil are inside the disi)

Posted by on

1 Suggested Answer

alicantecoli
  • 22041 Answers

SOURCE: I have a 1990 Toyota

never seen a petrol model of this one but i should imagine its either an earth or the take off for the rev counter .put a meter across the wires and chassis and see what happens ,then you will know whats the feed and whats not

Posted on Jan 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Ford Focus Error code PO320


P0320 - Ignition Engine Speed Input Circuit Malfunction The ignition engine speed sensor input signal to PCM is continuously monitored. The test fails when the signal indicates that two successive erratic profile ignition pickup (PIP) pulses have occurred.
  • Loose wires/connectors.
  • Arcing secondary ignition components (coil, wires and plugs)
  • On board transmitter (2-way radio)
The DTC indicates that two successive erratic PIP pulses occurred.

Oct 28, 2016 | Ford Cars & Trucks

1 Answer

I require simple wiring diagrams for a 1976 F150 pickup.


Use a test lite on negative side of coil, engine cranking, the lite should pulse?
It appears the vehicle has electronic ignition, There is a separate ignition module. In the wiring diagram, I can't guarantee the wire colors. The older my wirings diagrams are, it seems, the less accurate they are. I hope it is readable, If no spark, I'd check the ignition system, Check fuses--fusible links--battery connections.
26298806-sfpzqccw001mk5jkucj51ii1-5-0.jpg

26298806-sfpzqccw001mk5jkucj51ii1-5-2.jpg

Oct 02, 2016 | Ford F-250 Cars & Trucks

1 Answer

Wire up coil on my hilux yn65 with 3y engine with points


The ignition switch power wire goes to the terminal marked plus (+) on the coil, the coil terminal marked negative (-) goes to the distributor.

Sep 29, 2016 | Cars & Trucks

1 Answer

Ignition coil wiring diagram


I would probably go ahead and replace the components, at least with used parts as a trial.
Do you have the Delco system or the Magnavox system ? The Delco system has 3 small coils.

May 15, 2013 | Pontiac Cars & Trucks

2 Answers

I dont have any injector pulse.


Make certain there are no blown fuses to the engine controller or ignition system. Is there spark from ignition coil when engine is cranked over? If not, test your distributer pickup coil. If the pickup coil or ignition module are not functioning, you will not have injector pulse or secondary spark.
Good luck.

Jan 09, 2011 | 1991 Chevrolet S-10

1 Answer

Firing Order diagram for 2006 Ford Explorer


Hope this helps. The ignition coil:
  • changes low-voltage pulses from the PCM to high-voltage pulses.
  • fires 2 spark plugs simultaneously.
  • has 3 transformers.
    • One transformer fires the spark plugs for cylinders 1 and 5
    • One transformer fires the spark plugs for cylinders 2 and 6
    • One transformer fires the spark plugs for cylinders 3 and 4
Spark plug wires:
  • carry high-voltage pulses from the ignition coil to the spark plugs.
The spark plugs:
  • change high-voltage pulses to spark at the gap, which ignites the fuel and air mixture.
The firing order is 1-4-2-5-3-6.

69efa96.jpg

Jun 06, 2010 | 2006 Ford Explorer

1 Answer

How to remove a 1989 pickup chevrolet ignition coil ,6 cil.,chayane


GM Full-Size Trucks 1988-1998 Repair Information
Ignition Coil - REMOVAL & INSTALLATION
(sSee Figures 1, 2 and 3)

8182f5f.jpg

Fig. 1: Ignition coil mounting-4.3L engines
  1. Tag and unplug the wiring connectors from the coil and the coil wire.
  2. Unfasten the retainers securing the coil bracket and coil to the manifold.
  3. Remove the coil and bracket and drill out the two rivets securing the coil to the bracket.
  4. Remove the coil from the bracket.
To install:
The replacement coil kit may come with the two screws to attach the coil to the bracket. If not, you must supply your own screws.

df834a8.jpg

Fig. 2: Ignition coil mounting-5.0 and 5.7L engines

8dc14f4.jpg

Fig. 3: Ignition coil mounting-7.4L engines
  1. Fasten the coil to the bracket using two screws.
  2. Fasten the coil and bracket to the manifold. Tighten the retainers until they are snug.
  3. Engage the coil wire and the wiring connectors to the coil.

Hope this help to solve it (remember comment and rated this).

Apr 21, 2010 | 1989 Chevrolet C2500

1 Answer

Need wiring diagram


Go to autozone.com and register they have good wiring diagrams for your truck.What I saw was all the relays going to ground so you should have 12V coming off the ignition switch.

Jun 01, 2009 | 1990 Ford F150

1 Answer

I have a 1990 Toyota Hilux 4WD 3Y electronic ditributer engine. The ignition coil is inside the disi. The wiring has been tampered with and I need to know what the two wires do that go to the disi,...


never seen a petrol model of this one but i should imagine its either an earth or the take off for the rev counter .put a meter across the wires and chassis and see what happens ,then you will know whats the feed and whats not

Jan 10, 2009 | 1990 Toyota Pickup

1 Answer

Ignition coil for 1993 civic


best way to test is connect to car and see if it gives spark with engine turning, because it gets ground pulse from the distributer,if pulse id not coming to ignition coil, then you need to change distributor.

Aug 18, 2008 | 1993 Honda Civic 4 Door

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

424 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...