Question about Cars & Trucks

1 Answer

The heater blowis not working work - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,370 Answers

It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected.If its faulty it has to be replaced.


=======

For blower motor testing and replacing,check the link below:----
Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Posted on Nov 26, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater controls stop working and rear defrost inop and the park assit not working and we tried to program a keyless entry remote that didnt work eathier tried that and everything stop working


Did you check fuse's in fuse block center console ? Fuse #26 IGN3 / HVAC 10amp . Do you know what I'm talking about ?
Fuse Block - Center Console
Inside of console, behind the right console access panel
What did you do jump terminals in the DLC ?
You need a factory scan tool to program keyless entry remote .
  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool.
  4. Important: The scan tool must stay connected until all of the transmitters are programmed.
  5. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  6. Repeat the previous step in order to program up to 4 transmitters.
  7. Remove the scan tool.
  8. Operate the transmitter functions in order to verify correct system operation.

Oct 09, 2016 | 2004 Buick Rendezvous

1 Answer

Front demister not blowi g o to windscreen can only get air/heat onto face


Sticking defuse doors or control panel not making connections

Jun 12, 2016 | Cars & Trucks

1 Answer

2000 ford taurus heater not working. What can be wrong?


It sounds very much like the heater control door (inside the heater box) is sticking in one position or the other. It's intended to direct air through either the AC's evaporator or the heater core, depending upon whether you want heat or cooling.

Assuming (highly likely) that the control door is vacuum-operated, you may have a vacuum leak anywhere from the engine to the heater box inside the passenger compartment, via the heater control unit.

Nov 18, 2014 | 2000 Ford Taurus

1 Answer

WHY ECU FUSE KEEP BLOWIING ?


An electrical short to ground in the wiring harness on the vehicle is one possible cause. Fuses protect the wiring harness from burning up so don't use a bigger fuse or CAR-B-QUE time. Have someone competent you can trust so you can get it fixed instead of burning up fuses or the whole car.

Aug 30, 2014 | Cars & Trucks

1 Answer

I turn my heat on in the car it blows out air but know heat


has your antifreeze ever ran low or needed to be filled I had the problem needed to bleed the engine sounds funny but it had to be done then I had the best heat ever

Dec 20, 2012 | 1997 Mercury Mystique

1 Answer

Eng revers up when start up and in gear its coast at 18km and not much heat and fan not blowi too good.


It sounds like a vacuum leak. Take a spray bottle and place water in it and while the engine is running spray the water gentle around the hoses and manifold intake and see if the engine speed drops. If it does inspect that area for further repairs.

Mar 27, 2011 | 1996 Saturn SL

1 Answer

We bought a 1987 chevrolet S10 pickup from a private person and they to change out the motor as they did so a few things do not work right I was wondering if I could get a wiring diagram to make sure the...


Greetings Les: You don't need a wiring diagram to test your truck. Drive the truck and test everything including blowiing the horn, and turning on the lights. If you find something not working properly let's fix it we are here at FixYa to advise you and help you. You are bought a 1987 truck and there may be a few problems and expect to have to fix them. Les this is not a new truck coming from the factory. Congratulations on a great truck that will probably give you great service and good gas mileage if you take care of it. Good Luck

Oct 09, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

Heater stopped working


The heater core has gone out and will need to be replaced

Dec 07, 2008 | 2002 Mazda Millenia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...