Question about Cars & Trucks

1 Answer

Nissan pulsar n16/1.8 engine romoval without the gearbox?

Can i remove this engine without the gearbox? is there enough space to swing the engine away from the gearbox?,or will i touch the side of the engine compartment?

Posted by on

1 Answer

Drop the entire sub frame-- then work on the parts you need to
repair or whatever

If your doing the engine-- usually the transaxle comes out first

Your going to have trouble supporting it and the drive axles your way

Posted on Nov 26, 2012

  • shafiek gierdien Nov 27, 2012

    than you , i will try that and let you how it goes!

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how do i remove a gearbox from a 2004 mini

you can remove gearbox without eng
just done it !
you have to remove subframe and tilt eng
and it comes out of side

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: Removing a Matiz engine without the gearbox

Yes it can be done. I removed the battery and tray and gearbox mount only then was able to wriggle the motor out (after removing sarter,alternator,power steering and air con compressor). Also removing the plastic cover near the front pulley helped. Need small hands! Good luck!

Posted on Jun 11, 2009

  • 171 Answers

SOURCE: 1988 Nissan Pulsar will not engage clutch. Engine

You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Posted on Nov 15, 2009

jlisagearhea
  • 412 Answers

SOURCE: Car maintainance for Nissan Pulsar Vector 1990

Yes, Yes, Yes, and Yes.....All that you want to do you can perform yourself and save quite a bit of money.You can actually find a VERY VERY descriptive online manual(which i have too) at alldata.com You pay a $20 fee and you get online manuals for five years for one vehicle.Definitely worth it.This makes auto work much easier.Any other questions get back to me...I'M HERE TO HELP!!!

Posted on Dec 04, 2009

MNfisherman
  • 11896 Answers

SOURCE: how much fluid does an nissan pulsar n14 1991 gearbox

up to 8 quarts for the entire system

Posted on Dec 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 nissan pulsar st ckp sensor


very common for the N16 pulsars to log this code, this is a crank position sensor fault. 99% of the time is the cam and crank sensors. best to replace them both as a pair, Nissan actually sell them as a pair for this issue, non genuine ones are very un reliable and not much cheeper anyways. the cam sensor is in the back side of the head above the bell housing of gearbox and the crank sensor is in the bottom of the engine block at the gearbox end facing the firewall.
the other 1% is streatched orout of timed timing chains, but normally just the sensors will fix it.

Jan 12, 2014 | Cars & Trucks

1 Answer

The bolts connecting the driveshaft to the gearbox can it be fixed without replacing the gearbox? and how can i do this?


jack up car, remove wheels,ball joint, cv joint so the driveshaft hangs free. jack up engine a small bit then remove engine mount and lingage, lower the sub frame a small bit for room them let the engine down slowly, this will give you enough space to remove the bolt from the box. it a good bit of work so take your time and be safe.

Aug 23, 2010 | 1992 Volkswagen Jetta

1 Answer

Nissan pulsar '88. replaced starter motor, then


Is it a manual, or an automatic? Earlier Nissans sometimes have a problem with the neutral safety switch (a device that keeps the engine from rolling over in gear or without the clutch depressed.) Generally, if their bad, they need to be a little warm before they'll start, like setting in the sunlight for a few hours.

Good Luck!

May 22, 2010 | 1988 Nissan Pulsar

1 Answer

CV replacement


You don't have to pull the hub! No spring compressor needed. Either unhook the steering knuckle from the strut or thre lower ball joint and swing it out away from the car. Remeber to remove the brake calipers and tie rod ends to get more "swing". It takes a little palying with to manuver it out but you can do it.

Dec 26, 2008 | 1990 Nissan Pulsar

3 Answers

How do i remove a gearbox from a 2004 mini


I don't believe you are able to remove just the transmission , you may have to remove both as an assembly.

Dec 18, 2008 | 2004 Mini Cooper

1 Answer

Nissan Exa gear problem


Dear Customer,

As you said above your engine oil is goin lickage so find out any crack or pinhole on pipeline for collent oil rails.

replace oil pipies weld any crack found on transmision case thna your gear will work batter.

THNX

May 16, 2008 | 1988 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...