Question about Cars & Trucks

1 Answer

2006 Chevy Colorado high beams stay on why? - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 84 Answers

Probably because the little inside switch to turn them on and off using the lever attached to your steering column broke, if that's how your high beams turn on and off in that vehicle make/model. I had this happen in a Ford, and the cheapest quick fix is to unplug the high beams under the hood. At least that gets rid of the problem until you can find how to replace that switch and how much it will cost.

Posted on Nov 27, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: no high beams on a 99 chevy

look under your hood for the fuse/relay box will be on left side behind battery. the relay and fuses will be in there check fuses also

Posted on Aug 28, 2008

GM Elec
  • 1000 Answers

SOURCE: 2006 chevy colorado passlock comes on and stays

No, it can not be disabled.
The theft system is indicating a short term theft issue.
Have you added any "after market" remote start systems or alarms?
If NO.
Insert the key in the ignition, turn the key to run position ( do not start ) and leave it in that position for 10 minutes. Cycle the key to LOCK position, count to 10, then turn the key back to run position and leave on for 10 more minutes. After the 10 minutes is up, repeat the procedure (1) more time and the security system will relearn the PASS code.
Give it a try and let me know.
Regards,

Posted on Mar 23, 2009

  • 1 Answer

SOURCE: Passenger Low Beam Headlight needs replacement!!!

You could remove the air filter cover and then you will be able to reach the bulb.

Posted on Apr 22, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

  • 1 Answer

SOURCE: 2006 colorado intermittently fails to start. It

Clean all the electrical connections you can get to under the hood with automotive electronics cleaner,dry with compressed air and pack each connector with di-electric grease.

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to correct a 2005 chevy monte carlo high beams from staying on


About 17,700 results (0.74 seconds) Search Results

    My high beams won't go off!! - Monte Carlo Forum - Monte Carlo ...

    montecarloforum.com > ... > General Forums > General Monte Carlo Talk
    Jun 8, 2012 - i flipped on the high beams last night and i think that switch in the column broke. ... My high beams won't go off! ... 2003 Chevrolet Monte Carlo. Help!! Need to get headlights working. - Monte Carlo Forum ...
    Jan 1, 2012
    Repair Guide: List of Common Monte Carlo Problems and Solutions ...
    Aug 9, 2011
    Fog lights not working, High beams stay on?
    May 9, 2011
    More results from montecarloforum.com

Jan 30, 2016 | 2005 Chevrolet Chevrolet Impala LS

1 Answer

High beams flash but don't stay on


you'd have to play with it and see if it's related to maybe a stuck fog light or simply the high beam switch is junk

Mar 25, 2014 | 2006 Pontiac G6

1 Answer

Head lights aimed to high


Hello...

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 12, 2009 | 2005 Chevrolet Colorado

3 Answers

WHAT ARE THE SPECS TO ALIGN Headlights for 2006 chevy colorado


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 06, 2009 | 2006 Chevrolet Colorado

1 Answer

How do i change out the knock sensor on a 2006 chevy colorado


You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:
  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Sep 03, 2009 | 2006 Chevrolet Colorado

2 Answers

How do you adjust the headlights in a 2005 Chevy Colorado?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 15, 2009 | 2005 Chevrolet Colorado

1 Answer

Front lights


look at the head lights assembly. find some phillips screw there. two of them .either one on top and one on the side. these are the adjusting screws.

do it at night. park the car in front of a wall about 6 feet away and adjust the lights.

tnx 4 using fixya,


drcool



Nov 05, 2008 | 2006 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...