Question about Cars & Trucks

Open Question

How to fix code po7000 and po 888 on jeep liverty 2004

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 184 Answers

SOURCE: I have a 2004 Chev Colorado with PO 141 & PO 506 code

Hi, the P0141 is the O2 sensor, more info @ http://www.obd-codes.com/p0141 . Also P0506 code is Idle Air Controller problem - http://www.obd-codes.com/p0506

Posted on Jan 31, 2010

  • 6982 Answers

SOURCE: how often may i tune up my 2004 jeep liverty.

You can tune it up every day if you want to but you only need to do a major tune up about every 80K miles. It is good to give everything a "once over" at least once every two months...check the coolant level, air filter, hoses, drivebelt etc and clean / replace as needed and make sure there is nothing obvious that needs attention. Most important is to regularly check the oil level and change it when necessary. I use synthetics as they reduce friction (wear) and last longer than conventional lubricants.
good luck!

Posted on Apr 04, 2010

Testimonial: "i thank you for taking your time and give the information that lots of people will not want to give out. i am thank full. I live in St. Petersburg F"

  • 142 Answers

SOURCE: what does code po 0107 and po 1762 mean on a 2004

P1762 Governor Pressure Sensor Offset Improper Voltage0107 MAP sensor voltage too low

Posted on Nov 08, 2010

airman_slack
  • 96 Answers

SOURCE: 2003 dodge intrepid will not shift into third

It sounds like the TCM has reverted to Safe Mode because it has detected a problem.

http://www.obd-codes.com/p0700

Posted on Aug 22, 2012

ZJLimited
  • 17970 Answers

SOURCE: my 2003 dodge intrepid will not shift into third gear. code reader says po 700 and po 888 and transmission sensors have been changed also computer was flashed after used motor put in car

Hi there:
First I suggest complete trans flusing procedure done, and a transmission fluid modifier added at the same time. You might have a sticking valve in the valve body, and the flushing procedure may help that out if true. If not, you may still have a sticking valve in the valve body.

The P0700 code is stored in the ECM and just tell you that there is a code in the TCM (Transmission Controller), that is the P0888.



DTC P0888 is telling you that the Transmission Relay output is always off; in this link can checl the Diag Chart for that code, this coul help...







8_22_2012_9_52_07_pm.gif

Zoom Image link HERE

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Aug 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Overheated. Why won't it start?


I'm not really familiar with JEEP mechanics but if you've replaced your water pump and it's still overheating with full water/coolant level, you should check the thermostat; when it fails, it's a common cause or overheating in all kind of cars

I'm attaching some links to Youtube tutorial about replacing thermostat in a Jeep but you can expand your Google search using terms
Youtube replace thermostat JEEP Liverty

https://www.youtube.com/watch?v=Y3NpLdG993U

Jeep 4 0L straight six thermostat replacement

Thermostat Replacement Overheating fix Part 1 Jeep


How To Change the Thermostat in Jeep Wrangler


2002 Jeep Grand Cherokee Thermostat Replacement

Replacing the radiator thermostat in any Jeep Cherokee Jeep liberty Jeep...




Sep 10, 2015 | Jeep Liberty Cars & Trucks

1 Answer

Po316, po 300, po301, po305 2004 ford freestar


These codes are making me lean towards the ignition coil pack.My stepson's 2001 Sable 3.0 v6 had one cylinder misfiring(5-code P0305),which shares a coil with cylinder 1(code P0301).I diagnosed it by trading wire 1 and 5 at the coil,and the code changed to P0301.You have codes for the two cylinders on the same coil,so this is most likely it.(these codes would also trigger P0300(Multiple Misfires Detected) and P0316(Misfire Detected First 1000 Revs)).

Oct 14, 2012 | 2004 Ford Freestar

1 Answer

2003 dodge intrepid will not shift into third


It sounds like the TCM has reverted to Safe Mode because it has detected a problem.

http://www.obd-codes.com/p0700

Aug 22, 2012 | 2003 Dodge Intrepid

1 Answer

What is code p0203


PO 203---Injector Circuit Malfunction-Cylinder #3

Jul 11, 2012 | 2004 Jeep Grand Cherokee

2 Answers

Error codes po 134 po 153 po 154 po 155 po 171 po 174


PO 134 = 02 SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR1)
PO 153 =02 SENSOR CIRCUIT SLOW RESPONSE (BANK 2 SENSOR 1)
PO 154 =02 SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 2 SENSOR 1)
PO 155= 02 SENSOR HEATER CIRCUIT MALFUNCTION (BANK 2 SENSOR 1)
PO 171= SYSTEM TOO LEAN (BANK 1)
PO 174= SYSTEM TOO LEAN (BANK 2)
I WOULD SAY YOU HAVE FAULTY OXYGEN SENSORS CAUSING THE ENGINE TO RUN TOO LEAN REPLACE THEM AND YOU SHOULD BE BACK IN BUISNESS

Feb 23, 2011 | 2004 Suzuki Grand Vitara

1 Answer

What does code po 0107 and po 1762 mean on a 2004 jeep grand cherokee laredo?


P1762 Governor Pressure Sensor Offset Improper Voltage0107 MAP sensor voltage too low

Oct 20, 2010 | 2004 Jeep Grand Cherokee

1 Answer

OBD indicator light is on


The first thing is to have the computer scanned for the stored codes, the codes will tell you what is failing, for exaple there could be a code like po 173 saying o2 sensor heater curcuit high voltage, which nwould tell you that the o2 sensor is bad. so start with the scan, autozone and some other autopart stores will scan it for no charge. hope this helps.

Sep 16, 2010 | 2004 Jeep Grand Cherokee

1 Answer

How often may i tune up my 2004 jeep liverty.


You can tune it up every day if you want to but you only need to do a major tune up about every 80K miles. It is good to give everything a "once over" at least once every two months...check the coolant level, air filter, hoses, drivebelt etc and clean / replace as needed and make sure there is nothing obvious that needs attention. Most important is to regularly check the oil level and change it when necessary. I use synthetics as they reduce friction (wear) and last longer than conventional lubricants.
good luck!

Apr 03, 2010 | 2004 Jeep Liberty

1 Answer

PO137, PO 138 codes


well on my car these are reffering to the sensors in the exhaust, the upstream sensor(before the cat) and the downstream sensor(after the cat) the downstream sensor can act up if it is lazy or sluggish, or due to a bad catalytic converter or a clogged one. however there are sensors on the exhaust manifold which are determined by driver side or passenger,my opinion is to get a scanner for about $100 to $150 and you can figure out many of these codes yourself.

Jun 28, 2008 | 2004 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...