Question about 1997 Chevrolet Cavalier

1 Answer

How do you remove a starter from a 1997 chev cavalier?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,362 Answers

Here's a link on how to replace your starter.

Posted on Nov 26, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1997 chev. cavalier z24 Tranmission

I HAD THE SAME PROBLEM. I LOOKED IT UP IN THE HAYNES MANUAL IT SAID YOU HAVE TO JACK THE CAR UP LEVEL, AND THERE IS A PLUG ON THE SIDE OF THE TRANSMITION, YOU TAKE IT OUT IF FLUID COMES OUT THEN YOU ARE GOOD.

Posted on Mar 19, 2009

LEFTY64
  • 69 Answers

SOURCE: Reinstall of Starter 1998 2.4L Chev Cavalier

moz-screenshot-4.jpg

  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.

To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines
See Figure 10


0900c1528003cb99.jpg

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does my 1996 chev cavalier starts for a min then backfires an dies


The starter has nothing to do with your existing problem

Take it to a repair shop

Do not use it like that

Jul 16, 2014 | 1996 Chevrolet Cavalier

1 Answer

How to identify bad rear wheel bearings assembly on a 1997 chev. cavalier?


you should be getting a humming noise while driving check your cv joint bearing by turning your steering to left or right while driving if there bad you will hear a clicking noise

Jun 22, 2014 | 1997 Chevrolet Cavalier

1 Answer

I have a 1997 chev cavalier with new pluges, new fuel filter, new battery, starter, new compuer chip, new brakes car will turn over but not start, how can I tell if it is the timing gear, value, and how do...


Get a compression tester, remove all the spark plugs, unplug ignition module and injectors. Now screw in tester hose to cylinder #1, attach guage and crank engine for 3 seconds. Record reading on gauge and move to next cylinder. Repeat this on all cylinders. Compression should be around 90-100 psi and should not vary more than 20% between cylinders.

Aug 30, 2011 | 1997 Chevrolet Cavalier

1 Answer

1997 chev cavalier 2.2 ohv. hesitates when accelerator pedal applied. Completely tuned up 6 k ago,(except fuel filter), new o2 and coolant sensor. What is my next move.,


The TPS which is the throttle positioning sensor has an open in its circuit. Most auto parts stores will have this common part for you cars engine

May 23, 2010 | 1997 Chevrolet Cavalier

1 Answer

Replacing/removing radiator 1997 Chev Cavalier


Go to you public library they have repair manuals and diagram. Hope this helps and good luck.

Jan 07, 2010 | 1997 Chevrolet Cavalier

1 Answer

How do you check the transmission fluid level on a 1997 chev. cavalier 2.4


there is a plug in the trans. under the car that must be removed with the engine running to check the fluid level. take it to your local mechanic, have him check it for you, that would be the safest way to go

Nov 27, 2009 | 1997 Chevrolet Cavalier

1 Answer

What causes gears to change from reverse to drive in 1997 chev. cavaliers?


hydraulic pressure diverted by electronically/computer controlled solenoid valves inside the trans on the hydraulic heart of the trans the valve body.

Jul 19, 2009 | 1997 Chevrolet Cavalier

1 Answer

Belt tension


these belts are auto tensioned, if it has a problem the belt or the tensioner pulley are defective.

Jun 18, 2009 | 1997 Chevrolet Cavalier

1 Answer

Reinstall of Starter 1998 2.4L Chev Cavalier


moz-screenshot-4.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.

To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines
See Figure 10


0900c1528003cb99.jpg

Apr 08, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1997 Chevrolet Cavalier Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...