Question about 2000 Jeep Grand Cherokee

1 Answer

WHAT ARE THE SYMPTOMS THAT A FUEL PUMP NEEDS TO BE REPLACED ON A 2000 JEEP GRAND CHEROKEE

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It will not start or will idle rough or just die ....need to check to see if have pressure in the fuel rail...also turn key on and see if you hear the pump run in the fuel tank

Posted on Dec 17, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 27 Answers

SOURCE: HOW DO I CHANGE THE WATER PUMP ON A 99 JEEP GRAND CHEROKEE ?

At least you have the 4 liter 6. Once you get all the **** out of the way its like replacing a W/P on an "old school" engine, very much like a Ford or Chevy straight 6. 1) Remove radiator top retainer (the metal U that looks like its the top of the radiator (#13 or 14mm sockets I think). 2) To completely get if off you also have to remove the grill (4-6 phillips screws), then 3) unbolt it from the tubular bumper retainers underneath the grill. 4) DO NOT remove the latch cable - no need. 5) Remove the top bolts holding down the fan shroud. Lift the shroud off its bottom "tabs" and push over the fan. 6) Using #10mm socket remove fan from fan clutch, then remove bolts holding fan clutch onto water pump pulley. 7) Pull out shroud, then fan, then fan clutch. Be very patient, lots of wiggling may be needed. 8) Locate belt tensioner on idler puller below the Power steering pump. Losen very little the pulleys center bolt (10mm), then use a 10mm w/entension to losen the pulley's tension (use counter clockwise/normal rotation to losen). 9) Draw a diagram of the belt routing - you will Never remember it correctly otherwise. 10) Tap the w/p pully and pull if off - do not hit radiator fins! 11) Drain the radiator (clockwise/right rotation opens petoc from factory radiators - counterclock used on aftermaket rads). 12) Remove lower raditor hose at radiator, then at pump (it will be a challenge). 13) Remove upper radiator hose from rad and from thermostat housing. 14) losen the Rubber heater hose from the metal hose screwed into the W/P. 15) Remove 4 bolts from W/P (13 or 14mm I think). The one at the 4oclock position is longer than the others. One is hidden at 6oclock.
16) Remove 2 bolts (14-15mm??) on bottom of Power Steering mount - these go through the W/P case to the block. You may also need to losen the top PS bolts so the PS Bracket can be loose at the W/P case. 17) Wiggle the W/P out from under the PS bracket. and pull off. (16b if needed, remove the upper idler pulley near the A/C unit.) 18) Remove the Thermostat (upper hose return) housing. Scrape off old gasket. Replace with 160deg or 190deg thermostat. Use silicone on gasket. 19) Carefully use a 17 or 19mm box wrench to remove the metal heater hose return line from the upper part of the old water pump. Coat threads with spark plug thread antiseize and screw onto new W/P. 20) Install new W/P gasket w/silcone, be careful to Not block the water holes. 21) Slide W/P under the P/S bracket and jiggle into place. Hand thread one of the top bolts to hold the W/P in place. 22) Insert the P/S bracket bolts and lightly tighten. 23) Jiggle W/P around and insert other bolts, start with the 6oc hidden bolt. Add remaining bolts and tighten to 25 or 250?ftlb (about 3/4 past socket-snug). 24) Tighten ALL P/S bolts. 25) Adjust metal heater pipe. Reinstall rubber heater hose. 26) Reinstall W/P pulley and Fan clutch, and upper idler if it was removed. 27) Thread NEW Belt on pulleys. 28) Tighten tension on idler. Tighten idler axle bolt. 29) Install lower rad hose. 30) Slide shroud over pulleys. 31) Install fan on clutch. 32) Clip shroud retainer bolt mounts back on top of radiator. 33) Install shroud. 34) Connect upper hose. 35) Reinstall radiator retainer. 36) Bolt retainer to Tubular bumper mounts. 37) Reinstall grill. 38) Wonder where the extra bolts etc are supposed to go. 39) Cuss - pray -cuss - pray. 40 ) sip some beer. 41) carefully inspect everything to ensure its back to the way it looked before (several pictures from a digital camera taken during the disassembly will help). 42) Close the rad petok. 43) Add 1 gallons of antifreeze. 44) Start engine and add another gallon of A/F. 45) Turn heater controls to HOT inside (no need for fan). 46) Water guage should show 180 to 210F. 47) Add 1 gallon of water. 48) Install New 18PSI rad cap. 49) Turn off engine and add water or A/F to overflow tank. 50) 1 hour later open Cap to see if level has settled. Add Water as needed to fill rad.

Posted on Dec 31, 2008

whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

  • 6982 Answers

SOURCE: 2000 jeep grand cherokee 4.0 liter engine timing belt replacement

If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Posted on Apr 05, 2009

  • 58 Answers

SOURCE: replace fuel filter on 1997 jeep grand cherokee

If you have the V8 engine, the filter is actually part of the fuel pump. WHICH IS IN THE TANK

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Grand Jeep Cherokee Limited, V 8. Just died at a red light. We got push it to the side of the road and 2-3 mins it started. This has happen 3-4 times. What could be the problem?


Right after it stalls (and you are in a safe place) Turn the key on and listen for the fuel pump to come on (in the tank). If you don't hear it, likely it is going bad. When they do that, the pump gets hot and binds...after it cools off it starts working again.
If you can hear the pump, chances are that the crank position sensor is failing. The symptoms are nearly identical.

Mar 05, 2011 | 2000 Jeep Grand Cherokee

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

2 Answers

200 jeep grand cherokee...it's fuel pump time, can


not a good idea if its the main fuel pump on engine.
it needs a dial guage to set it up, its complicated to some 1 new.
you need to see it done 1st.
a lot of people i know dont do this, it wastes so much fuel its un real.
what engine have you got, what is the prob with your vehicle. is it leaking.
what make is your pump. get back to me.

Aug 17, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Is the fuel pump and the fuel pressure regulator in the same assembly on a 2000 jeep grand cherokee


the fuel pump and fuel pressure regulator are 2 different parts, the regulator is on the engine the fuel pump inside the gas tank.

Jul 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee Limited Fuel Filter


Sorry brother, it is in the gas tank with the pump. they used filters that are suppose to be good for the life of the vechicle. you can see the plug if you lift up your spare. hope you dont HAVE TO go in there.

Mar 16, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Fuel fileter


Get under the vehicle and start at the fuel tank and go forward you will find it. If its a Grand Cherokee Laredo the fuel filter is located inside the fuel pump so the whole fuel pump has to be replaced

Nov 30, 2008 | 2000 Jeep Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...