Question about 1996 Ford Aerostar Extended

1 Answer

I have a 1997 fordareostar im trying too get my starter out i removed the battery cable and the bolts i cant get it outpast the exaust pipe do i have too remove it do0ea any1 no how too get it out it comes away from the flywheel but i have no room too totally remove so i can rep-lace it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,646 Answers

You may have to lift the motor some to have clearance

Posted on Feb 23, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 45 Answers

SOURCE: how to remove starter from 1995 ford crown victoria

yes they are very difficult to get to.
its just the top one and some mechanics leave them out after starter replacement.
it sounds bad but true.
i use either a stubby 10 mm wrench and a prybar to break it loose,
or a 3/8 ratchet and a wobble extenion and socket. it has to be the perfect length using different extensions to reach and still fit with the ratchet handle at the back of the starter.
sorry but it can be done.....
no stubby wrench, cut one

Posted on Feb 11, 2009

jaysonemanme
  • 500 Answers

SOURCE: have a Ford F250 Super Duty Turbo 7.3L engine. The starter was removed and I am trying to install a new starter. I'm not sure about the wiring. I cannot find the Solenoid Relay, and currenlty I have t

yes that is right- 2 wires 1 big and 1small both go on the starter 1 is hooked directly to the batt and 1 to fuse box

Posted on May 21, 2009

  • 15 Answers

SOURCE: Can't replace the TR Sensor on my 1997 Ford Taurus.

Hi; get a stool or ask someone with long arms to pop iy out, make sure that the same you pop it out is the same way you can put it back in, or you will need to reset the gear shift. Good Luck!

Posted on Jun 06, 2009

  • 811 Answers

SOURCE: 1997 ford f150 4.2 L engine starter mount bolts

take old bolts to auto parts store and match

Posted on Sep 13, 2009

  • 1 Answer

SOURCE: cant remove starter on 86 f250 -6.9 diesel

I have a 1986 f-250 diesel like yours and I replace the starter this spring and had the same problem. Just keep working it and don't be afraid to bend things out of the way, or hit it with a hammer to loosen it.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant remove my starter from 1997 fordareostar


CAR STARTER REMOVAL? TESTING


One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----


How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html ----------- How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------
How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------
2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----
Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

Oldsmobile starter solenoid replacement procedure?...

--------------------

How to replace Oldsmobile starter moor?

----------

Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

Nov 26, 2012 | Cars & Trucks

1 Answer

Trying to find starter bolts


4.5L and 4.9L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the starter motor shield.
  4. Remove the exhaust front and rear pipe assembly.
  5. Remove the flexplate inspection cover.
  6. Disconnect the solenoid 'S' terminal nut and battery cable nut.
  7. Unbolt the starter motor mounting bolts, and remove the starter motor.
zjlimited_1565.jpg

Fig. Later model starter location and mounting on the 4.9L engine

Hope this helps (reemember to rate this answer).

Jul 10, 2011 | 1992 Cadillac DeVille

1 Answer

How do i change the starter on a 1997 buick park avenue?


Removal & Installation To Remove:
Starter 9306xg03.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Disconnect the battery negative cable
  3. Raise and support the vehicle
  4. Remove the transmission cooler line clip if necessary
  5. Remove the torque converter cover
  6. Disconnect the battery positive cable from the starter
  7. Disconnect the wire from the starter solenoid S terminal
  8. Remove the 2 starter motor mounting bolts and the starter motor
To Install:
  1. Install the starter motor
    • Torque the mounting bolts to 32 ft-lbs (43 Nm)
  2. Connect the battery positive cable to the starter
    • Torque nut to 12 ft-lbs (16 Nm) (1997-2000);
    • Torque nut to 89 in-lbs (10 Nm) (2001-2005)
  3. Connect the starter motor S terminal wire
    • Torque nut to 22 in-lbs (2.5 Nm)
  4. Install the torque converter cover
    • Torque the bolts to 115 in-lbs (13 Nm)
  5. Attach the transmission cooler line clip
  6. Lower the vehicle
  7. Reconnect the negative battery cable
prev.gif next.gif

Dec 09, 2010 | Buick Park Avenue Cars & Trucks

1 Answer

WHAT STEPS DO I TAKE TO REPLACE A STARTER ON A TOYOTA COROLLA


REMOVAL & INSTALLATION 4A-F, 4A-FE and 7A-FE Engines
  1. Disconnect the negative battery cable.
  2. Remove the air cleaner assembly (with hose).
  3. Disconnect all the wiring from the starter terminals.
  4. Remove the starter mounting bolts. Remove the starter. To install:
  5. Attach the connector to the terminal on the solenoid switch. Connect the cable from the battery to the starter and secure with the nut.
  6. Place the starter in the flywheel bellhousing, tighten the mounting bolts to 29 ft. lbs. (39 Nm).
  7. Install the air cleaner assembly.
  8. Connect the negative battery cable.
  9. Check the starter for proper operation.
4A-GE Engine
  1. Disconnect the negative battery cable. Remove the both engine under covers.
  2. Remove the front exhaust pipe.
  3. Remove the electric cooling fan.
  4. Disconnect all the wiring from the starter terminals.
  5. Remove the starter mounting bolts. Remove the starter. To install:
  6. Attach the connector to the terminal on the starter solenoid. Connect the cable from the battery to the terminal on the switch and secure with the nut to 29 ft. lbs. (39 Nm)..
  7. Install the electric cooling fan.
  8. Install the front exhaust pipe.
  9. Install the left and right engine under covers.
  10. Connec the negative battery cable.
  11. Check that the starter works properly.
prev.gif next.gif

Oct 15, 2010 | 1997 Toyota Corolla

1 Answer

How do you remove a starter on a 1997 GMC Jimmy?


1995-97 4.3L MODELS and 1995-99 2.2L models

5ed4c74.jpg

Fig. 5: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.
To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope helps.

Sep 07, 2010 | 1997 GMC Jimmy

1 Answer

I WANT TO KNOW WHERE IS THE STARTER LOCATED SO I CAN REPLACE IT..


REMOVAL & INSTALLATION 2.0L SOHC Engine With Automatic Transaxle; 2.4L Engine
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the air cleaner resonator.
  3. Remove the 3 bolts attaching the Transmission Control Module (TCM). Do not disconnect the TCM wiring. Move the TCM to gain access to the upper starter mounting bolt.
  4. Remove the upper starter mounting bolt.
  5. Raise and safely support the vehicle.
  6. Remove the positive battery cable nut and disconnect the cable from the starter.
  7. Disconnect the push-on solenoid connector.
  8. Remove the lower mounting bolt that attaches the starter to the transaxle.
  9. Remove the starter from the vehicle. Fig. 3: Starter motor wiring terminal connections — 2.0L SOHC engine with A/T; 2.4L engine 90902g12.gif
    To install:
  10. Install the starter onto the transaxle and the lower mounting bolt.
  11. Tighten the mounting bolts to 40 ft. lbs. (54 Nm). NOTE: Before reconnecting the wiring to the starter solenoid, be sure to clean the wiring of any dirt or corrosion.
  12. Reconnect the positive battery cable to the solenoid post and tighten the retaining nut to 90 inch lbs. (10 Nm).
  13. Reconnect the push-on solenoid connector.
  14. Lower the vehicle.
  15. Reinstall the upper attaching bolt and torque to 40 ft. lbs. (54 Nm).
  16. Reinstall the TCM to its original location and install the mounting screws.
  17. Reinstall the air cleaner resonator.
  18. Reconnect the negative battery cable.
2.5L (VIN N) Engine
  1. Disconnect the negative battery cable.
  2. Most vehicles will require the removal of the front exhaust pipe. Use penetrating oil on the fasteners to ease removal.
  3. Disconnect the starter motor electrical connections.
  4. Remove the starter motor mounting bolts and remove the starter. Fig. 4: Exploded view of the starter motor mounting — 2.5L engine 90902g10.gif
    To install:
  5. Clean both surfaces of the starter motor flange and the rear plate. This is important since the starter grounds through its case and the transaxle flange to which it attached. Some remanufactured starters may have paint on these areas which should be cleaned off before installation. Install the starter motor onto the transaxle and secure with the retaining bolts. Tighten the bolts to 20–25 ft. lbs. (26–33 Nm).
  6. Connect the electrical harness connectors to the starter.
  7. Connect the negative battery cable and check the starter for proper operation.
2.5L (VIN H) Engine
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Raise and safely support the vehicle.
  3. Loosen, but do not remove, the exhaust pipe-to-manifold retaining nuts.
  4. Place a drain pan under the oil filter to prevent oil spillage, then remove the oil filter. For additional details, refer to Section 1. Fig. 5: Loosen the exhaust pipe-to-manifold retaining nuts to provide removal clearance for the starter 90902p01.jpg
    Fig. 6: Location of the positive battery cable nut (1) and the push-on solenoid connector (2) 90902p02.jpg
    Fig. 7: After removing the oil filter for access, unfasten the retaining nut and disconnect the positive battery cable 90902p03.jpg
    Fig. 8: Disengage the push-on starter solenoid connector 90902p04.jpg

  5. Remove the positive battery cable retaining nut and battery cable from the starter.
  6. Disconnect the push-on solenoid connector.
  7. Remove the 3 bolts that attach the starter unit to the transaxle.
  8. Pull the exhaust pipe down just enough to provide clearance for the starter motor. The exhaust pipe does not have to be separated from the pipe-to-manifold threaded studs.
  9. Remove the starter unit from the vehicle. Fig. 9: Remove the 3 starter motor-to-transaxle housing attaching bolts 90902p05.jpg
    Fig. 10: Pull the exhaust pipe down just enough to provide removal clearance for the starter 90902p06.jpg
    Fig. 11: Carefully remove the starter motor from the vehicle 90902p07.jpg
    To install:
  10. Install the starter unit onto the transaxle and install the 3 mounting bolts.
  11. Tighten the mounting bolts to 40 ft. lbs. (54 Nm). NOTE: Before reconnecting any wiring to the starter solenoid, clean the wire terminals of any dirt or corrosion.
  12. Reconnect the positive battery terminal and retaining nut to the starter solenoid post. Tighten the retaining nut to 90 inch lbs. (10 Nm).
  13. Reconnect the push-on solenoid connector.
  14. Reinstall the oil filter.
  15. Lower the vehicle.
  16. Reconnect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1997 Chrysler Sebring

2 Answers

How to change a starter on a 4.3 gmc sonoma 1997


STARTER REPLACEMENT ( 1995-97 4.3L MODELS )

ad8746e.jpg

Fig.: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.

To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope this help (remember rated this help) Good luck.

May 11, 2010 | 1997 GMC Sonoma

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

2 Answers

I am trying to locate the starter of my 1998 LS 400 pls. help me.


The starter is located under the intake manifold on this engine.

20d8b81.gif

Jun 17, 2009 | 1998 Lexus Gs 400

1 Answer

Trying to find the location of the starter


Try looking on the front side of the engine between the oil filter and transmission.

Removal & Installation
  1. Remove or disconnect the following:
    • Negative battery cable
    • Starter harness connectors
    • Starter motor
To install:
  1. Install or connect the following:
    • Starter motor. Torque the bolts to 35 ft. lbs. (47 Nm).
    • Starter harness connectors. Torque the battery cable nut to 100 inch lbs. (11 Nm).
    • Negative battery cable

Jul 25, 2008 | 2000 Dodge Grand Caravan

Not finding what you are looking for?
1996 Ford Aerostar Extended Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...