Question about 2008 Hyundai Veracruz

Open Question

Position light bulb replacement/Access to bulb?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change back brake light bulb n/s


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

Apr 30, 2011 | Volkswagen Golf Cars & Trucks

2 Answers

I cant seem to find out how to remove the tail light to replace the bulb. what am i missing?


Typically, the entire tail light assembly has to be released from the inside. So you have to remove trim, inside, for access, usually 3 or 4 thumbscrews get released and the whole thing comes out. This set up is much more watertight than the older method of lense removal.

Mar 26, 2011 | 1993 Buick Roadmaster

1 Answer

Is there a trick to getting to the rear turn signal on a 2003 ford focus hatchback. I had removed the screw to the lens cover but I still cannot gain access to the turn signal bulb to replace it.


Replacing tail/brake/backup lights and turn signal bulbs (coupe)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. From inside the luggage

compartment remove the wing nut

of the rear light assembly cover.

3. Using a Phillips screw driver

remove the screw. The lamp is still

retained by a spring loaded clip.

Remove by gently pulling out the

light housing.

4. Turn the bulb socket counterclockwise as far as possible and pull it

out.

5. Pull the bulb straight out of the socket.

Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (sedan)

1. Make sure the headlamp control

is in the OFF position and then

open the trunk.

2. From inside the luggage

compartment remove the three wing

nuts of the light housing.

3. Gently pull the light housing to

the outside.

4. Turn the bulb socket

counterclockwise and pull it out.

5. Pull the bulb straight out of the socket.
Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. Using a screw driver remove the

fixings and trim from the body.

3. Remove the socket from the lamp

assembly

4. Pull the bulb straight out of the

socket.
Install in reverse order.


Hope this helps.

Zeppelinx12

Mar 03, 2011 | 2003 Ford Focus

1 Answer

Replacing headlight bult in 1997 explorer


REMOVAL & INSTALLATION Examples of various types of automotive light bulbs tcca6p11.jpg
Fig. 1: Exploded view of the front headlight assembly and related components 85556040.gif
If equipped, open the headlight access panel by sliding the latch and lifting the panel upwards 89686p34.jpg
Fig. 2: Exploded view of the headlight bulb, retainer and wire harness plug 89686g17.gif
  1. Open the vehicle's hood and secure it in an upright position.
  2. If necessary, open the bulb access panel by depressing the latch then lifting. To remove the bulb, grasp the retainer and rotate it counterclockwise to unlock it . . . 89686p35.jpg
    . . . then withdraw the bulb from the headlight lens housing 89686p36.jpg

  3. Unfasten the locking ring which secures the bulb and wire harness plug assembly, then withdraw the assembly rearward.
  4. Disconnect the electrical wire harness plug from the bulb and remove the locking ring as well. Unplug the wire harness from the bulb and either slide the retainer over the plug, or remove it from the bulb 89686p37.jpg
    To install:
  5. Before connecting a light bulb to the wire harness plug, ensure that all electrical contact surfaces are free of corrosion or dirt.
  6. Install the locking ring onto the bulb, then line up the replacement headlight bulb with the harness plug. Firmly push the bulb onto the plug until the spring clip latches over the bulb's projection. WARNING
    Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.
  7. Position the headlight bulb and secure it with the locking ring.
  8. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
  9. Close the bulb access panel and the vehicle's hood.
prev.gif next.gif

Feb 09, 2011 | 1997 Ford Explorer AWD

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

Need to replace headlight?


  • Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  • 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  • 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  • 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight I would replace them both sides if i were you
  • Dec 02, 2010 | 2004 Chrysler Crossfire

    2 Answers

    How do I access the front left indicator light for


    2fac621.gif
    To change a front parking/turn signal lamp bulb on Town & Country models, remove the screw, and hinge the lamp on the tab


    b2dedfc.gif
    With the lamp free of the facia, the bulbs can be accessed by twisting the sockets counterclockwise, and pulling the bulb from the socket

    1.Pull the bulb straight out of the socket.
    2.Replace the bulb.
    3.Installation is the reverse of the removal procedure.
    4.Verify light operation.

    Jan 19, 2010 | 1996 Dodge Caravan

    1 Answer

    Bulb Failure position option


    the position bulbs are located in the trunk and you access them the same way you access the tail lights im not sure what the bulb does but its a 10 dollar fix. FYI when you replace the bulb the message center will still tell you that it has failed you have to take it to the dealer to have them to erase the message (i just left mine it seemed a waist of money)

    Sep 01, 2009 | 2004 Volvo S60

    1 Answer

    Replace headlight


    Review this guide...

    Fig. 1: Examples of various types of automotive light bulbsf32f79e.gif

    Fig. 2: Exploded view of the front headlight assembly and related components
    0f608b7.gif

    Fig. 3: If equipped, open the headlight access panel by sliding the latch and lifting the panel upwards
    6fbe95d.gif

    Fig. 4: Exploded view of the headlight bulb, retainer and wire harness plug
    3af8aa1.gif

    - Open the vehicle's hood and secure it in an upright position
    - If necessary, open the bulb access panel by depressing the latch then lifting.

    Fig. 5: To remove the bulb, grasp the retainer and rotate it counterclockwise to unlock it ...
    1a6adbb.gif

    Fig. 6: ... then withdraw the bulb from the headlight lens housing
    39a120c.gif

    - Unfasten the locking ring which secures the bulb and wire harness plug assembly, then withdraw the assembly rearward.

    - Disconnect the electrical wire harness plug from the bulb and remove the locking ring as well.

    Fig. 7: Unplug the wire harness from the bulb and either slide the retainer over the plug, or remove it from the bulb
    d77665a.gif

    To install:
    - Before connecting a light bulb to the wire harness plug, ensure that all electrical contact surfaces are free of corrosion or dirt.
    - Install the locking ring onto the bulb, then line up the replacement headlight bulb with the harness plug. Firmly push the bulb onto the plug until the spring clip latches over the bulb's projection.

    WARNING:
    Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.

    - Position the headlight bulb and secure it with the locking ring.
    - To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
    -
    Close the bulb access panel and the vehicle's hood.

    Good luck... and remember rated my help!

    Aug 07, 2009 | 1998 Ford Explorer

    2 Answers

    Message board states "Bulb Failure Position Light: What is this>


    Hello mtsign

    This a problem with "A" bulb, no real way to find the problem one unless you test the output of each bulb. You will have to replace them one or two at a time. Start with the rear bulbs as they get the most use i.e. brake lights. Sounds strange but, over time a bulb will lose it's strength and the computer picks it up as a bad bulb and sends the message, quite common with these vehicles. I would use quality replacement bulbs or you could be chasing around weak cheaper bulbs for a while. Hope this helps and good luck.

    Feb 12, 2009 | 2004 Volvo S60

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    66 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8269 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...