Question about Cars & Trucks

Open Question

Norton dominator rear hub diagram

Rear wheel and hub layout

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

95_Bravo
  • 16 Answers

SOURCE: Rear wheel bearing diagram

The bearing is pressed in so you will have to carry the hub to a machine shop to have the old bearing pressed out and the new bearing pressed in once you have the hub off the car.

Process to remove hub is as follows (from the 1990 Miata Service manual)

Remove rear wheel, rear wheel brake caliper assembly (suspend with a rope), and disc plate.

Check for rear hub play with a dial indicator, if excessive play either tighten the locknut or remove hub and replace bearing.

To remove bearing bend up the locknut stake and remove axle nut - torque is between 159 - 217 ft pounds.

Now remove the hub, retaining ring, rear wheel knuckle, wheel bearing (if loose), dust cover.

Replace with new parts, locknut, dust cover, knuckle bushings and hub bolts (if worn).

Take knuckle with wheel bearing to machine shop and have old bearing pressed out and new bearing pressed in.

Assembly is reverse of the above.

I have personally found that by the time I pay a machine shop to do the removal and reinstall of the bearing and take my time into account it is less expensive to pay a good shop to do this work for me.

DIY information at Miata.net

Posted on May 10, 2009

  • 23 Answers

SOURCE: rear wheel hub

IF IT HAS REAR DRUM,WITH WHEEL REMOVED,REMOVE BRAKE DRUM,KNOCK OFF CENTER BEARING CAP,REMOVE STAKED LOCK NUT,AND PULL OF HUB AND BEARING ASSEMBLY.

Posted on May 16, 2009

  • 21 Answers

SOURCE: please describe how to replace rear wheel hub asse...

Its simple just remove the wheel. open two bolts of the clipper dont for get to release the park braks. reaove the dics or drum. in the hub there will be a hole so install a sockt through there and there r four bolts in there. open all four and spray some lubricant before u start opening the bbolt so u dont mess up anything. with the help of a hammer the just give it a slight hit so it comes out. but my advise will be tht u get the hub assembly and hub. because they r sold seprate... tighten all the bold and dont for get to pump the brakes after ur finished..

Posted on May 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

How to install wheel bearing hub assemble (front)1998 on a ford escort


front or rear?

Assuming rear, on the brake drum:

Hub Removal
  1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
  1. Remove the wheel hub.
    1. Unstake the rear axle wheel hub retainer.
    1. Remove the rear axle wheel hub retainer and discard.
    1. Remove the wheel hub (1104).

Nov 05, 2009 | 1998 Ford Escort

1 Answer

I need a rear suspension diagram for a 1999 Mercury Cougar


0218b1b.gif
Item Part Number Description 1 Body mounting cup 2 Spring seat 3 Spring 4 Strut 5 Crossmember 6 Stabilizer bar 7 Front arm 8 Rear arm 9 Wheel spindle 10 Tie-bar 11 Dust cap 12 Brake drum 13 Hub retaining nut 14 Hub and bearing assembly 15 Backing plate 16 ABS sensor 17 Tie-bar mounting bracket

Sep 02, 2009 | 1999 Mercury Cougar

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

We are trying to replace my rear wheel bearing. Can anyone give any ideas how to get it apart?


here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

06017-esca-g92.gif
06017-esca-g93.gif
06017-esca-g94.gif
06017-esca-g95.gif 06017-esca-g96.gif

To install:
  1. Install or connect the following:
    • Wheel bearing in to the knuckle
    • Snapring
    • Wheel hub into the wheel bearing
    • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake drum
    • Rear wheel
    • Negative battery cable
06017-esca-g97.gif
06017-esca-g98.gif

Apr 11, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...