Question about 1995 Ford Thunderbird

Open Question

Blend door actuator on ford t-bird

Removing and replacing blend door actuator on1995 ford t-bird LX

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: trying to remove dashboard to access blend door actuator and

www.heatertreater.net

Posted on Jan 04, 2009

Ad
emissionwiz
  • 76164 Answers

SOURCE: blend door actuator on a 99 expedition

In order to replace the blend door actuator motr dribe u must remove the entire dash assembly, I strongly suggest buy a factory service manual for this job which takes around 12 hours to complete, also take pictures of connections u are not sure of before u disconnect them./

Posted on May 19, 2009

harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

roniecon
  • 6826 Answers

SOURCE: need to locate blend door actuator on 2002 ford

Open the glove box,and look on top of ac/heater box toward the center of vehicle,it should be setting right there.

Posted on Oct 10, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

2 Answers

Air blend actuator 2000 ford explorer is not working?


First, insure you do not have a vacuum leak or bad vacuum check valve. If this is all good, you may have to change actuator and every model has a different way to access this--some require dash removal. If you must do this, get a shop manual as the air bags CAN BE VERY DANGEROUS!

Mar 28, 2016 | 2000 Ford Explorer Eddie Bauer

1 Answer

How to remove an actuator on 2001 ford f150 xlt


You need to google 2001 f150 blend door actuator replacement. It is slightly right of center above the plastic duct work for the floor area. All lower dashboard plastic is removed to get at it.
Then the ducting is removed.
http://www.autozone.com/repairguides/Ford-Pick-Ups-Expedition-Navigator-1997-2000/Heating-and-Air-Conditioning/Blend-Door-Actuator/_/P-0900c152801e55ed

Jul 05, 2014 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Top blend door actuator on 2011 f150


You need to google 2001 f150 blend door actuator replacement. It is slightly right of center above the plastic duct work for the floor area. All lower dashboard plastic is removed to get at it.
Then the ducting is removed.
http://www.autozone.com/repairguides/Ford-Pick-Ups-Expedition-Navigator-1997-2000/Heating-and-Air-Conditioning/Blend-Door-Actuator/_/P-0900c152801e55ed

Feb 17, 2014 | Ford Freestar Cars & Trucks

1 Answer

Heating and defrost unit does not work but its getting power


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks) This is well documented problem on this make and model.

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 08, 2012 | 1997 Ford Thunderbird LX

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

1 Answer

How To Replace The Heater Core In A 1997 Ford Thunderbird LX


Heater Core Removal
  1. Partially drain the cooling system.
  1. Remove the tube gasket from the heater core tubes.
  1. Remove four heater core access cover retaining screws and remove the access cover from the A/C evaporator housing (19850).
  1. Remove A/C electronic blend door actuator.
  1. Slide heater core (18476) and seals from the A/C evaporator housing.
Installation
  1. Install the heater core in the A/C evaporator housing with the tube gasket on the outside of the case.
  1. Install A/C electronic blend door actuator as described.
  1. Position the heater core cover on the A/C evaporator housing. Install the four retaining screws.
  1. Refill the cooling system.


    1a302ce.gif




    Item Part Number Description 1 18596 Heater Core Tube Gasket 2 18476 Heater Core 3 18B300 Heater Core Cover 4 390747-S2 Screw (4 Req'd) 5 18N267 Heater Core Cover Seal


    Hope this helps... Cobra

Jun 12, 2010 | 1997 Ford Thunderbird LX

2 Answers

A/c temp on max 27 a/c temp on norm 50?


Was browsing the ford f-150 forum and found that Ford has a lot of issues with it's AC, some too hot and some like yours, way to cold. At MAX it should read around 42. Best 2 solutions I've found are:
  • Blend door/Blend door motor
  • Dirty EVAP coil
Here's a pic of what the Blend door/Motor look like and instructions on how to replace it. Wish you the best of luck.

Removal & Installation
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
  3. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  4. To install, reverse the removal procedure.



b23881e.jpg

May 09, 2009 | 2002 Ford F250 Super Duty SuperCab

Not finding what you are looking for?
1995 Ford Thunderbird Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...