Question about 1995 Pontiac Grand Am

Open Question

Need timing marks diagram for 1995 Pontiac grand am

Put new timing chain in 1995 Pontiac grand am . Need a diagram of timing marks to set the timing.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 462 Answers

SOURCE: need timing marks for a 1996 pontiac grand am se 2.4 DOHC

YOU WILL SEE A HOLE IN THE CAM GEAR THAT A 3/8 BOLT WILL FIT INTO. PUT A BOLT INTO THE HOLES OF BOTH CAM GEARS. THEN LINE UP THE CRANK PULLEY KEYWAY AT ABOUT 12 O'CLOCK WITH THE MARK ON THE ENGINE BLOCK.

MAKE SURE TO COMPRESS THE CHAIN TENSIONER AND RELEASE IT WHEN THE CHAIN IS IN POSITION.

Posted on May 31, 2009

  • 883 Answers

SOURCE: 2001 Grand Am timing chain diagram

rate me FIXYA!....thanks!
11b1d5f.jpg
66c8573.jpg

Posted on Jul 05, 2008

ewashmidas
  • 362 Answers

SOURCE: need timing chain diagram for 2002 pontiac grand

Here you go. 391888b.png

Posted on Mar 09, 2009

  • 6982 Answers

SOURCE: timing chain mark diagram for a 94 grand am????

Haynes lists the entire procedure for setting the position of the cams etc. Positioning of these is critical...If off by even a slight amount the valves WILL strike the pistons and destroy the engine. DO NOT use any parts made by SA Gear...They have no quality control and will deny any claim made against them. Make sure that the chain guides are in good condition and that the chain tensioner is operating properly.

Posted on Apr 15, 2009

  • 6982 Answers

SOURCE: where are the timing chain marks ona 2000 pontiac grand am

On a 2.4, there are no timing marks...There are holes in the cam gears that need to be aligned with corresponding holes in the head.
Though it's not terribly difficult to do, it must be done precisely according to instructions or valves will hit the pistons and destroy the engine. You can find instructions for this procedure in haynes and other vehicle service manuals. (too long to write out here).
Remember...this is an exact install...you cannot just get close!!!
Good luck! Post back if you need further specific instructions with any part of the job.

Posted on Apr 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Diagram of timing chain


I need to know what year Grand Am and engine size?

Aug 27, 2014 | Pontiac Grand Am Cars & Trucks

1 Answer

How to set the timing on a 1997 pontiac grand am 2.4 twin cam ?


ok after removing all the parts out of the way and the damper off make sure its on number 1 and the mark on the damper is inline with the mark on the block is at TDC then you get a long bolt and insert it in the whole to the bottom of the cam sprocket intake and exhaust then set the chain tensioner make sure you hear it click but the new one come set now after you would of put on the chain rotate the engine by hand and make sure the tensioner jumps out to the chain then put everything back up and start your engine

May 07, 2014 | 1997 Pontiac Grand Am

1 Answer

I have a 1993 jeep grand cherokee 4.0l and need a diagram for the timing chain links. i was told that there is to be 15 links between marks and then told 20. need help please.thanks


I don't have a diagram I can post, but once you install the new chain and have the two timing marks pointing toward each other, then turn the Crankshaft around twice and see if the two timing marks still line up. Remember, the crankshaft turns two times for every one time the camshaft turns.

I understand the 15 vs. 20, but that's neither here nor there. What the Factory Service Manual states is there should be 15 "pins" between the timing marks when the timing chain is set up properly. (?) The links you speak of aren't what you're counting...it's the pins in the chain. In other words, for each link of the Timing Chain, there are two pins, holding it in place...or a total of 48 pins on the length of the entire timing chain. Personally? When I install a timing chain, I rotate the crankshaft around twice to see if the timing marks still match up, and before putting everything back together, I start the Engine for a brief few seconds thereby knowing after reassembling everything, the Engine WILL Start.

If you're still concerned about the 15 pin thing, stop by your local Dealership and look in the Factory manual in Section 9 (Engine), Page 36 for a picture of the 15 so-called "chain-pins."

Hope this helps,

~00 Buck~

"Still living on the Right Side of Dirt..."

May 18, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Replacing a timing chain on a 96 grand am. need a


it is a good idea to get a haynes repair book on your type of car it will give u step by step how to do it,,it is not much,,,

Apr 24, 2010 | 1996 Pontiac Grand Am

2 Answers

Need diagram 99 pontiac 2.4 timing chain. tapping noise under cover


If you are talking about 99 Pontiac Grand Am, I have the information you need with drawings. If you send me your email address I will send you the info you need. Outdoorsman592003@yahoo.com

Sep 09, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Need timing marks for a 1996 pontiac grand am se 2.4 DOHC


YOU WILL SEE A HOLE IN THE CAM GEAR THAT A 3/8 BOLT WILL FIT INTO. PUT A BOLT INTO THE HOLES OF BOTH CAM GEARS. THEN LINE UP THE CRANK PULLEY KEYWAY AT ABOUT 12 O'CLOCK WITH THE MARK ON THE ENGINE BLOCK.

MAKE SURE TO COMPRESS THE CHAIN TENSIONER AND RELEASE IT WHEN THE CHAIN IS IN POSITION.

May 31, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Timing chain diagram


Just wrap the chain around the gears and lineup the dots. dot to dot and put them on. That's how it goes. The timing itself is not adjustable. It's controlled by the engines computer. It's that simple.

Apr 27, 2009 | 1990 Pontiac Grand Am

1 Answer

Timing chain mark diagram for a 94 grand am????


Haynes lists the entire procedure for setting the position of the cams etc. Positioning of these is critical...If off by even a slight amount the valves WILL strike the pistons and destroy the engine. DO NOT use any parts made by SA Gear...They have no quality control and will deny any claim made against them. Make sure that the chain guides are in good condition and that the chain tensioner is operating properly.

Apr 15, 2009 | 1994 Pontiac Grand Am

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...