Question about Ford Contour

Open Question

Location of camshaft position sensor 1998 Ford Contour 2.5L

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76682 Answers

SOURCE: camshaft position sensor location

At the right rear of the engine under the intake manifold and to the left of the oil filter. You will probably need to go under the car to spot it, it's the sensor with a three-wire connector arranged vertically. But you can take it out from above. It's held in with a single bolt with an eight MM head located just above the sensor. Un-clip and remove the electrical connector. Unscrew the bolt with a socket wrench & extension bar. Wiggle and pull the sensor out.
here is a picture.
255f615.jpg

Posted on Apr 10, 2009

Ad
  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

  • 14036 Answers

SOURCE: 98 silverado 5.7L camshaft position sensor

ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Posted on Oct 23, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a throttle position sensor on a 2000 ford contour


Hey DonAld, these are not hard to replace..( I do not know which engine you have..it makes a difference!! ).. take a PICTURE of where the current TPS os positioned and located... the radial (adjustment) location IS critical!!..
here is a link to Autozone, ...O'Reilly's, and Advance Auto should have one too..

Ford Contour Throttle Position Sensor TPS

https://www.oreillyauto.com/shop/ignition---tune-up-16776/engine-sensors-17084/throttle-position-sensor-12043/2000/ford/contour?q=tps

Advance Auto Parts Down for Maintenance

Feb 03, 2017 | 2000 Ford Contour

1 Answer

Cant locate the camshaft position sensor on my 2000 ford contour 2.5L V6


On the 2.5 liter V6, it's just below the front cylinder bank valve cove

Jan 11, 2017 | 2000 Ford Contour

1 Answer

98 contour p1380 po340


Po340 camshaft position sensor a bank 1 circuit malfunction p1380

May 25, 2012 | 1998 Ford Contour

1 Answer

I can not seem to find a timing position sensor for my 1998 ford contour gl. does anyone know where i may get one? it is a 4-cylinder.


there is no timing position sensor. there are cam and crank sensors they are on the front cover and near the valve cover.

May 13, 2011 | 1998 Ford Contour

1 Answer

Where is the thermostat located?


aaronsnipes_0.jpg

Disconnect the camshaft position sensor electrical connector. Disconnect the coolant hoses and position to one side. Unscrew (3)bolts and remove the thermostat housing.

Mar 07, 2011 | 1999 Ford Contour

2 Answers

1998 Ford Ranger 4.0 engine Engine will not start Code is Camshaft position sensor. Where is this located


It is behind the intake manifold in the center of the block, on the rear of the engine.

Jan 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

Where is the 1998 ford 4 cylinder 2.0 camshaft sensor located


On the back of the engine just above the cylinder head.

Oct 21, 2010 | 1999 Ford Contour

1 Answer

I nee instructions on a cam sensor removal for a 1998 ford contor with a 16 vale 2.o over head cam engine


The camshaft sensor is located at the back of the head on driver side. Remove the wire,unscrew the sensor,screw the new sensor in the head and put the wire back on the sensor

The camshaft sensor is not in the back on the 98 4 cyl its right in front. All you need to do is take off the 3 bolts on the top of the heat shield and pull it back a bit and it will be right there.

Apr 24, 2010 | 1998 Ford Contour

1 Answer

Where is the camshaft position sensor located on a 1999 ford contour?


what is your engine size?? give me the eighth vin number starting from left to right..then i will be able to help you..

May 16, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...