Question about 2004 Dodge Ram 1500

1 Answer

Where are the 6 bolts to remove the bed of a

How to remove a of bed of a truck

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Crawl under the truck , 2 is at the frt of the bed ,then look inside of the chasis rails at the back 2 near the bumper and 2 between those bolts and the rear end located inside the rails also . there is a small wire on the right frt to remove as well as the 3 screws in the fuel door area you must remove to lift the bed

Posted on Nov 30, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a fuel sending unit in a 1999 Dodge ram 1500


Just as you said ,remove the 8 bolts and get a couple buddys and lift the bed and slide back onto the bumper. This will give you the room needed to do the job.4 bolts up front( 2 on each side) and 4 in the back. Much easier if you had a chain hoist but lifting works too. I don't know if it will lift up enough to do the job with enough room. It was real simple to get the bolts back in place so no worries. Hope this reply isn't to late.

Oct 04, 2015 | Dodge Cars & Trucks

1 Answer

How do you remove the bed of a 98' Chevy S10 step


disconnect all electrical connections between the frame and box, disconnect the fuel filler hose from the box or the fuel tank, there are 4-6 bolts that mount the truck bed to the frame to remove. move truck bed.

Sep 25, 2014 | Cars & Trucks

1 Answer

How do i remove the truck bed from 2005 chevrolet avalanch


disconnect all electrical wiring that is attached to the bed then disconnect the fuel filler tube. there is 4 bolts that hold the bed to the frame that you will have to remove. some trucks the bolts are removed from inside the bed and others from under the bed though the frame. then get help to pickup the bed and turn it to gain access to the pump or remove the bed from the frame.

Sep 19, 2014 | 2005 Chevrolet Avalanche

1 Answer

How to remove truck bed 2002 gmc sonoma


There are 4 bed bolts under the bed on each side that need removed, also 1 bolt on each side for the ground for the tail lights, and 3 screws in gas door for the filler neck. And then get a couple buddies to help lift off the bed or use tie-down straps and an engine lift and lift the bed off.
Thank you and good luck,
Lee

Nov 12, 2010 | 2002 GMC Sonoma Extended Cab

1 Answer

How to replace 2001 s10 pickup fuel pump


This is not a full answer, but a tip on an easier way.to get to the pump. Instead of removing the gas tank. Just pull the bed off the truck! I guarantee that it will be easier. I did this on a 2001 S10 and it took less that an hour to remove the bed.
Remove the spare tire, and the tube that the tool to lower the tire goes through. You will need to unplug your tail lights under the back or the bed on both sides. There is also a grounding screw for the tail lights on each side that needs to be removed. Remove the screws that hold the gas tank filler hose to the side of the bed - right by the filler cap. Remove the tailgate (to make the bed lighter). Follow the frame down the length of the bed and you will find the bolts holding the bed on. There should be 6 or 8 bolts. My S10 had 8 bolts and my son's full size Chevy PU had 6 bolts (go figure?). Then just lift the bed off the truck. We did my S10 with 3 people and it had a camper shell and rack on it. My son's full size truck was lifted off with only 2 people. I would suggest 4 people however - one on each corner to make it easier to lift and control.
Replace the pump as described above and then you can start the engine to make sure everything works before setting the bed back on. NOTE: The fuel pump grounds back with the tail light ground. If the engine doesn't start right away, try grounding the wire back by the tail lights. It works like a charm. This is an especially nice way to do it if the gas tank is full! I spent 18 years as a professional mechanic and this is one of the slickest, least known tricks I have come across. I wish I'd known about it when I was wrenching for a living! Cheers!
cb6f5baf-9d72-4319-b871-6eae67d521ce.jpg

Apr 20, 2010 | 2001 Chevrolet S-10

1 Answer

AndFuel filler tank has gone bad, best way to


To be quite honest, in my past experience,the easiest way to replace it is to remove the bed. Take out the three small bolts inside the fuel door. Unplug the wire harness from the rear bumper area, take out the 6 bolts that hold the bed on. If it's a six foot bed, or even an 7 foot bed, it's pretty easily lifted by 2 people. It can be done on a lift by leaving the bed on. But I've removed somewhere in the area of 10 of these in the last year. Less time consuming to just pull the bed off.

Feb 22, 2010 | 1994 Ford Ranger Supercab

1 Answer

2000 Chevy Silverado 2500 6.0 litre fuel pump


lifting the truck bed off the frame works best if you dont have a lift..take the fuel neck loose from bed and remove bolts holding bed to frame from the drivers side..loosen the bolts on passenger side..raise the bed on drivers side while watching bumper to bed clearance on passenger side.. you should get enough clearance to remove fuel pump from tank

Dec 26, 2009 | 2000 Chevrolet Silverado

1 Answer

Fuel line leaking on top of gas tank of a 1993 chevy s-10 pick up carburator.what is the easiest way to fix besides dropping the tank.


dont want to drop tank than raise the bed remove filler neck bolts than under the truck remove the bolts for the bed with help from some friends lift up bed and remove but than disconnect wire harness for rear lights or raise up and support bed with wood across frame rails high enough to get to fuel lines

Sep 27, 2009 | 1993 Chevrolet S-10

2 Answers

Need 2001 dodge 1500 fuel pump replacement diagram


make sure you get the right pump, you need to know your tank size. then take off your bed. you have i believe 6 bed bolts, disconnect tail lights (unplug from underneath) remove bed grounding strap 1 screw, remove bed with help. Disconnect wires, unscrew fuel pump, replace pump. Reverse order to replace bed. jim

Jun 11, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How do u remove the bed from a 2001 chevy?


get under the bed you have 4 to 6 bolts that run on each corner of the bed to frame rails , look thru holes in frame for big bolt heads to remove the bed, easy , hope this helps you ,thanks robert b.

Jun 07, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...