Question about Cars & Trucks

Open Question

Codes p2101,p2110.p2111,2112 on a 2007 caliber

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 149 Answers

SOURCE: wont start

The sensor ($100) in the throttle body ($400) is dirty and your engine is running high mix of gas. If you do not get it fixed, it will melt your catalytic converter ($1000) and stop up your muffler and your car will not run until you clean out the muffler system. If your car is not running, test this by disconnecting the exhaust manifold and try to start it.

Posted on Dec 24, 2009

Ad
Donut Boi
  • 22 Answers

SOURCE: I went to a ranch

all those codes you have posted are related to the throttle and sensors it sounds like you have water in the wiring etc in this part of the truck, does it run ok? if so i would run it for 15 to 30mins reset all codes and try agen it might dry its self out in a few days

Good Luck Tom

Posted on Jan 17, 2010

Testimonial: "It's missing a little. The only problem the accelerator pedal is not working since it is a Electronic Throttle body. Hopefully that get's fixed to."

TDISLine
  • 1874 Answers

SOURCE: i have a 2006 mercury

1. Remove the throttle body and clean carefully inside.

Posted on Feb 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Working on 2003 Lincoln LS 3.0. code p2110; p2107. Customer replaced throttle body


P2110 - Throttle Actuator Control System - Forced Limited RPM. Throttle actuator control system is in FMEM mode of forced limited RPM.
  • PCM damaged
  • Cross wired TACM motor
DTC indicates only that FMEM condition exists, and can be set incombination with DTCS P2100, P2101, or P2107, meaning the ETB faults should be repaired first.
P2107 - Throttle Actuator Control Motor Processor. The ETC control area of the PCM failed self test. Fault could be the result of an incorrect TP command, or the TACM wires shorted together.
  • TACM wire shorted together
  • TACM circuit wires shorted to pwr
  • PCM damaged
  • ETB damaged
An (TACM) circuit PID reading may indicate a fault if available
DV21 CHECK ETC MOTOR FOR SHORT OR OPEN
  • Remove ETC motor harness connector.
  • Measure the resistance between the TACM + and TACM - pins, through the motor.
Is the resistance less than .8 ohms, or greater than 1000 ohms?
Yes No Replace Throttle body assembly. note: Clear DTCS and rerun self test, if DTCS (P2100, P2106, P2112), or (P2100, P2106, P2111, P2112) are output GO to DV22 , for (P2100, P2106, P2107) GO to DV23 , and for (P2100, P2106, P2107, P2111, P2112) GO to DV24 , and for DTCS (P2101, P2106, P2110, P2111, P2112) GO to DV25 . GO to DV22 . DV22 CHECK ETC MOTOR HARNESS FOR OPEN
  • Remove PCM harness connector.
  • Measure the resistance of the TACM+ circuit between the PCM and TACM harness connectors.
  • Measure the resistance of the TACM- circuit between the PCM and TACM harness connectors.
Is the resistance less than 5 ohms?
Yes No GO to DV23 . Repair open circuit. DV23 CHECK ETC MOTOR HARNESS FOR SHORT TO GND, PWR, ETCREF, AND ETCRTN
  • Measure the resistance between the TACM + pin and battery gnd.
  • Measure the resistance between the TACM - pin and battery gnd.
  • Measure the resistance between the TACM + pin and battery pwr.
  • Measure the resistance between the TACM - pin and battery pwr.
  • Measure the resistance between the TACM + pin and ETCRTN.
  • Measure the resistance between the TACM - pin and ETCRTN.
  • Measure the resistance between the TACM + pin and ETCREF.
  • Measure the resistance between the TACM - pin and ETCREF.
Are both resistances greater than 10K ohms?
Yes No GO to DV24 , for P2101, GO to DV25 . Isolate and repair short circuit. DV24 CHECK ETC MOTOR HARNESS FOR CIRCUITS SHORTED TOGETHER
  • Measure the resistance between the TACM + pin and TACM- pin.
Is the resistance greater than 10K ohms?
Yes No GO to DV25 . Isolate and repair short circuit. DV25 CHECK FOR CROSSWIRED ETC MOTOR HARNESS
  • Measure the resistance between the TACM + pin and TACM- pin.
Is the resistance greater than 10K ohms?
Yes No GO to DV26 . Properly wire the TACM per TACM and PCM connector diagrams. DV26 SELF TEST VEHICLE
  • Key On Engine Off.
  • Clear DTCS.
  • Cycle accelerator pedal to the floor and back several times.
  • Self Test vehicle noting any DTCS.
Were there any DTCS related to the ETC system?
Yes No Intermittent fault, GO to Z1 Replace PCM.

Oct 13, 2017 | Lincoln Cars & Trucks

1 Answer

How do i fix?


P0122 throttle/pedal position sensor/switch A circuit low input
P0223 throttle/pedal position sensor/switch B circuit high input
P2101 throttle actuator ctrl motor circuit rang/perf
P2104 throttle actuator ctrl sys-forced idle
P2110 throttle actuator ctrl sys-forced limited rpm

Here is the meaning of the codes hope this helps

Sep 20, 2015 | Cars & Trucks

1 Answer

Code p2110, p2118 and p0746


Google the codes & read up

It's all there on many sites

Study OBD2 Systems

OBD P2110 etc

Feb 28, 2014 | Cars & Trucks

1 Answer

2006 Suzuki forenza codes p2110, p2135, p2101, p2135, p0106


denise, this is a double post. go back one.
keep in mind, the ECU never knows what part is bad, ever.
only a tech, can find the truth. (testing)

Sep 16, 2013 | Cars & Trucks

1 Answer

2013 chrysler 200 electronic throttle indicator comes when engine starts jerking


My car is reading codes P0121 P0221 P0223 P0123 P2135 P2101 P2110 P2111 P0562

Aug 30, 2013 | Chrysler Cars & Trucks

1 Answer

I went to a ranch and there were large puddles of water that I went thru. Now my truck has different codes ex.p p0122,p0223,p2101,p2110. What could it be?


all those codes you have posted are related to the throttle and sensors it sounds like you have water in the wiring etc in this part of the truck, does it run ok? if so i would run it for 15 to 30mins reset all codes and try agen it might dry its self out in a few days

Good Luck Tom

Jan 17, 2010 | Ford F-150 Cars & Trucks

1 Answer

Wont start


The sensor ($100) in the throttle body ($400) is dirty and your engine is running high mix of gas. If you do not get it fixed, it will melt your catalytic converter ($1000) and stop up your muffler and your car will not run until you clean out the muffler system. If your car is not running, test this by disconnecting the exhaust manifold and try to start it.

Dec 25, 2008 | 2007 Suzuki Reno Hatchback

1 Answer

Trouble Shooting Codes


It sounds like the throttle position sensor (TPS) needs to be replaced. When the TPS sensor goes bad it will give you the codes you received.

Sep 29, 2008 | 2006 Suzuki Reno

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

633 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...