Question about 2005 Dodge Durango

Open Question

Transfer case motor on a 2005 dodge durango

How to install a trasfer case on a 2005 dodge durango or can you just disconnect the 4X4 all together

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 217 Answers

SOURCE: getting rear gears out of the difential case 1999 dodge durango

  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Posted on Feb 11, 2009

  • 116 Answers

SOURCE: egr valve dodge durango

if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Posted on Apr 24, 2009

BCally1
  • 133 Answers

SOURCE: 1999 Dodge Ram 4X4 vacuum diagram

that line is just the breather tube for the tcase. the 4x4 vacuum lines are hard plastic lines that run from the tcase to the front axle disconnect

Posted on Jul 28, 2009

polarcycle
  • 1392 Answers

SOURCE: reprogram 2005 Dodge Durango key fob

Go to the dealer. It is the only way, they have to use a computer. Changing the battery doesn't make it lose it's program though. You most likely broke the battery hold down. This is the most common thing I see at my shop. If the key still starts the vehicle, you now have a bad key fob. If not, you may be able to get it reprogrammed.

Posted on Aug 05, 2009

  • 10 Answers

SOURCE: 1999 dodge ram 4x4 transfer case

is your fluid the right grade check shift linkage loose or worn or binding manual shift or bad shift fork or moter on automatic shift

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 dodge dakota 4x4 transfer case stuck in 4 w low


Does the transfer case actuator motor move at all?

Jan 25, 2017 | 2005 Dodge Dakota

1 Answer

How do i replace shift motor in 2005 durango


I doubt if the encoder motor is causing the transfer case to stay in low 4WD. It is more likely a problem inside the transfer case.

Jun 04, 2013 | Cars & Trucks

1 Answer

2005 dodge durango it changes into 4lo by itself


This problem and similar ones are being reported on a daily basis. Dodge reports that the problem lies with the transfer case motor. I suggest that you have the dealer take a look since this is probably a fix that will be done on Chrysler's nickel.

Jun 22, 2012 | 2005 Dodge Durango

2 Answers

Whats the svc 4x4 indicater ligthmean


It means your 4 wheel drive system needs to be serviced or is detecting a malfunction.

Jan 18, 2011 | 2005 Dodge Durango

3 Answers

How do you use 4WD on a 1999 dodge durango?


there are 2 systems.
one is a part time system only.the 4x4 locks and is for ice mud and snow.Driving full time will damage the transfer case.The other system is a full time system and the selector says 2wd,4wd part time ,4wd full time and 4 lo. if in full time,it can be driven all the time even on dry roads.The full time is really an all wheel drive system.
the 4low is a very low gear and the main shifter has to be put in neutral and then the transfer case put in 4 low.attempting to put it in 4 low while in "drive" will make a gear grinding noise.
getting out of 4 low is the opposite.shifter to neutral and then put it in 2wd and then in drive.The newer durango has an electronic transfer case with a dial on the dash.The 2002 was available with 2wd,4wd,awd and 4 lo on a switch.The 1999 has the lever on the floor .

Feb 12, 2010 | 1999 Dodge Durango

1 Answer

I have Ford Ranger Supercab 2001. The 4wd does not engage.. clicking sounds from under the dash board. Please help :)


When you turn the dial to 4 wheel drive it controls a solonoid unit that then controls the electric motor that shifts the trasfer case to 4X4. The clicking sound that you are hearing is probobly the solonoid unit (4x4 control unit) engaging or trying to engage the trasfer case motor. From what I,ve heard the solonoid unit is located behind the plastic panel that is under the glove box and before the passenger side door. Moisture can build up in that area and ruin the solinoid unit over time. Check any fuses that have any thing to do with the 4x4. If the solonoid unit or fuses is not the problem, I would check the wireing to the electric transfer case motor and the motor itself. Good luck and God bless!

Oct 16, 2009 | 2000 Ford Ranger SuperCab

2 Answers

2005 Ford F150, 5.4L V8, 4x4; The transfer case


Encoder motor located on the transfer case is usually the problem. It is the motor that shifts the transfer case.

Sep 28, 2009 | 2005 Ford F-150

Not finding what you are looking for?
2005 Dodge Durango Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...