Question about 2000 Jeep Grand Cherokee

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6

I would like a step by step process on how to remove and change the water pump on my 2000 Jeep Grand Cherokee

Posted by on

  • 1 more comment 
  • poedunk65 Mar 14, 2009

    I have the same issue on a 2001 grand cherokee with the inline 6 cyl.



    I fully do not understand all the technical descriptions about this. Please explain in laymens terms. Viscous assembly???



    Does the shroud come out?? The shroud has an electric cooling fan mounted to it does this come out with the shroud also??



    What about the pully on the pump shaft, how does that come out?



    Thanks,

  • brian calhoon
    brian calhoon May 11, 2010

    what motor

  • Anonymous Mar 15, 2014

    Water is inside 2000 jeep grand Cherokee and condensation gets front area wet inside

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

1 Suggested Answer

motor1258
  • 6674 Answers

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

Here you go.Clicking on any of the pictures will expand them.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004319c

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing the fuel filter on a Jeep Grand Cherokee


most 2004-2007 Cherokees v6 and v8 models only had a strainer on the fuel pump jeep does make a replacement fuels line assembly with a fuel filter

Apr 04, 2014 | 2006 Jeep Grand Cherokee

1 Answer

Flush heater core on 2000 grand cherokee


If it's clogged it can be cleared with the use of Garden hose pump. The water has to be turn into the heater hose line and then water has to be removed out via the pump.

==========

For complete step by step procedure, refer heater core flushing and other help links mentioned below.


======

Click the link below: -----

------------

How to Flush Heater Core?
http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html
-------
Also check these link too:---

HEATER CORE REPLACEMENT, HEATER CORE REMOVAL, TROUBLESHOOT HEATER CORE, FLUSH HEATER CORE,
http://alltypesofpartsreplacing.blogspot.com/2012/12/heater-core-replacement-heater-core.html

------
These will help.
Thanks.

Dec 25, 2012 | 2000 Jeep Grand Cherokee

3 Answers

Heater not working


can you smell antifreeze if so its the heater core

Dec 02, 2012 | 2000 Jeep Grand Cherokee

1 Answer

I'm trying to locate the thermostat on my 2000 jeep grand cherokee


  1. On 2000 Jeep Grand Cherokee 4.7L V8
  2. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  3. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

2000 Jeep Grand Cherokee 4.0l v6
Note:on the In-line 6 4.0L model the thermostat housing is mounted at the top of the engine block next to the water pump.

Nov 14, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Water pump replacement


haynes repair book,,it is good to have if u plan on keeping the truck,,,,tells u step by step,,

Apr 20, 2010 | 1998 Jeep Grand Cherokee

1 Answer

95 jeep grand cherokee water pump


YOU HAVE TO REMOVE FAN SHROUD FIRST BEFORE YOU CAN REMOVE THE FAN WITH CLUTCH ATTACHED.

Apr 15, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Do i have to take off the radiator to change the water pump on a 6cyl. ?


Yes, you will need to remove the radiator to change the water pump.  Good luck! thanks for an honest rating.

May 19, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Need to replace water pump


It's not an impossible job, but too long to write out instructions. I suggest that you get an inexpensive manual for your car (haynes is about $20) and follow instructions there. If you run into any specific problems, give me a shout! (just curious ...why are you changing the pump?)

Mar 23, 2009 | 1997 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

3 Answers

Change a water pump


1. Remove negative battery cable
2. Open radiator valve - drain cooling system
3. Remove cooling fan and shroud
4. Remove belt
5. Remove water pump pulley from hub
6. Remove hoses from water pump
7. Loosen heater hose coolant return tube mounting bolt and nut.
8. Remove the tube. Lose the O-Ring.
9. Remove water pump mounting bolts
10. Loosen the clamp on the bypass hose.
11. Remove the hose as you pull the pump away from the engine.

Hope this helps

Mike

Jun 14, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

1,232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...