Question about 2001 Jaguar S-Type

1 Answer

Right tail lamp failed

I changed all the bulbs but still they don't work. The only one that is working right now is the stop sign.

Posted by on

  • MS Jag Mar 05, 2009

    i had the same problem you need to change the fuse which is located in your fuse box in the trunk.



    MS Jag

  • Anonymous Mar 26, 2014

    Rear bulb fail light came on, replaced bulbs, got the same message bought a new tail light assembly, still the same message and the reverse lamp doesn't work.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

Check all the fuses, if fuses ok, then check the wire at the light connection, the jag is really a ford along with its faults, common fault is the earth on the light and the light bulb holder also plays up

Posted on Feb 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Chevy Trailblazer left rear taillight will not work. Brake light, back up light & turn signal all work. Right rear all work. Replaced bulbs, switched sides, still nothing.


There was a recall on this, see your local Chevrolet dealer.... Recall Date: NOV 01, 2004 Model Affected: 2003 Chevrolet Trailblazer Summary: ON CERTAIN SPORT UTILITY VEHICLES, VIBRATION AND HEAT MAY CAUSE THE TAIL LAMP/STOP LAMP BULB TO LOOSEN IN ITS SOCKET. IF THIS OCCURS, THE BULB MAY FLICKER AND EVENTUALLY BECOME INOPERATIVE. Consequences: AN INOPERATIVE BRAKE LAMP WILL NOT CONVEY THE DRIVER'S INTENTION OF STOPPING TO DRIVERS IN FOLLOWING VEHICLES, AND AN INOPERATIVE REAR TURN SIGNAL LAMP WILL NOT CONVEY THE DRIVER'S INTENTION TO TURN TO DRIVERS IN FOLLOWING VEHICLES. BOTH OF THESE FAILURES CAN INCREASE THE RISK OF A CRASH. Remedy: DEALERS WILL INSPECT THE TAIL LAMP/STOP LAMP ASSEMBLIES, AND IF NECESSARY, REPLACE THEM. THE RECALL BEGAN ON NOVEMBER 22, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438, OLDSMOBILE AT 1-800-630-6537, BUICK AT 1-866-608-8080, OR GMC AT 1-866-996-9463. Potential Units Affected: 871473 Notes: GENERAL MOTORS CORP. Read more: http://www.motortrend.com/cars/2003/chevrolet/trailblazer/recalls/#ixzz2jWJ1eDyR

Nov 02, 2013 | Cars & Trucks

1 Answer

2004 right rear tail light/ brake light not working


these may not work unless the vehicle is running as leds require a certain amount of power to work..also check the ground wires..turn on 4 way flashers and see what the lights do.. repost..

Jan 30, 2013 | 2004 Cadillac Escalade

1 Answer

My dashboard and rear lights don't work


Assuming this has the V6, the 15A PARK LPS fuse in the underhood fuse block feeds constant power to the auto park lamp relay. When the relay closes, 12V power passes through the 10A INST LPS fuse in the right instrument panel fuse block to the panel dimmer switch and then to the five instrument cluster lamps.

If by "rear lights" you mean everything in the rear lamp assemblies, power for the tail lights (running lights) starts at the 15A PARKLAMP fuse in the underhood junction block, passes through the automatic lamp control (ALC) relay and the right instrument panel junction block to the tail filament of the dual stop/tail lamp and the separate tail lamp on each side. The 12 V power for the stop lamps is protected by the 20A STOPLAMPS fuse in the left I/P junction block, passes through the stoplamp switch when brakes are applied, stop filament of the dual stop/tail lamps. That leaves the turn signals and the hazard lamps. Power for the turn signals originates at the 10A TURNLAMPS fuse in the left I/P junction block and is applied to the hazard switch. Switch output goes to the turn/headlamp/wiper switch for selection of left or right turn signals. That switch output goes to the turn lamp. Power for the hazard function begins at the 10A HAZRD LPS fuse in the left I/P junction box and goes to the hazard switch. Switch output is sent to the left I/P junction box to make the turn signals flash. That's it. Post a comment if you need more information.

Sep 15, 2012 | 2002 Oldsmobile Alero

2 Answers

2004 Chrys Concorde, new utility trailer, tail light converter. Problem: There is output from conv box in yellow wire, when turn signal is on, but when it is connected to the trailer harness, no output...


Your vehicle CANNOT be wired for a trailer without using the converter box. The only vehicles that do not require a converter box are the vehicles that use the stop lamp bulb as a turn signal. Your vehicle is equipped with SEPARATE stop lamp and turn signal bulbs.

To make the converter box work correctly, it must be wired according to the instructions to BOTH the stop lamps AND the turn lamps. The tail (or PARK) lamps DO NOT go through the converter box.
Your trailer uses the SAME bulb for stop and turn - THIS is the reason you need a converter.

The wire color for both your LEFT TURN and your RIGHT TURN are LIGHT GREEN/TAN. Although the wire colors are the same at the bulb sockets, these are SEPARATE circuits and must be wired to the correct wire at the converter box. (LEFT and RIGHT) The converter box will have an INPUT connection for EACH of these.

The wire color for your STOP lamps is WHITE/TAN. The converter box should only have one INPUT wire that connects to this. It doesn't matter which side of the vehicle you connect this wire to. All of the stop lamps are on the same circuit.

The converter will then have only one wire for LEFT turn and stop (usually YELLOW) this is the wire that needs to go to your trailer connector for left turn and stop.
The RIGHT turn and stop will most likely be GREEN coming out of the converter.

Sep 05, 2011 | Chrysler Concorde Cars & Trucks

1 Answer

How do I change a brake light bulb in a 1999 c70 volvo?


Welcome to FixYa.com
Brake Lamp Replacement

Location of the lights

Image

The illustration shows the locations of the lights on the RH side. The LH side is the same but

mirror-reversed.

The lights have the following functions:

- 1 +1 = Parking light Fail light

- 2 = Reversing light

- 3 = Fog light LH side only (LHD cars)

- 5 = Direction indicator

- 6 = Brake light

Image

Tail light changing bulbs

Ignition off.

Open the cover in front of the tail light

Undo the wing nut and take out the lamp holder.

Change the defective bulb.

Fit in reverse order.

Check that all bulbs lamps are intact and in working order.

Image

Replacement of tail light cluster

Note! If a new tail light is to be fitted, the sleeves must be ground down 1.5 mm.

Open the cover in front of the tail light Undo the panel partly in front of the tail light Unplug the

connector for the tail light Undo the four nuts securing the tail light see illustration.

Pull the tail light straight out. Fit in reverse order

Note! check the sealing and fit on reassembly.

Check that all bulbs lamps are intact and in working order.Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician

Jan 27, 2011 | 1999 Volvo C70

1 Answer

2001 jaguar s type - Right tail lamp failure message.... I replaced bulbs and fuse and tail lights still don't work but the dual element right break light does illuminate when I press the break also right...


There is a harness that you unplugged for the rear tail lamp. Make sure it is fully pressed and locked. This is always the cause on jags for tail lamp failure.

Dec 14, 2010 | 2001 Jaguar S-Type

1 Answer

1998 Jeep Grand Cherokee Left Tail/Stop Light Inop.


You need to check for power and ground. If you dont have a volt meter you can get a good cheap one from radio shack. If there is no power recheck with a known good ground. All the lights on that side share a common ground. Check the sockets for signs of burning or corrosion. There is a plug in the left rear quater panell. If you have no power check the corrisponding wire at that connector. The wires splice togeter just before the connector. So if the other brake/tail light is working you know the problem is after that. Hope this helps. Im sure you'll find the problem.

Feb 08, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Jaguar S-Type Logo

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...