Question about Chevrolet 1500

1 Answer

Rust removal how to remove a visor on a 64 chevy pick-up

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Use a wire wheel the rust should come right off. Want be no damage to truck.or sand blast it.

Posted on Feb 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

04 MGM, had rust in the battery terminals and it would not start after I cleaned started immediately now the Power locks, cabin, globe box, visors, and trunk lights dont work!all fuses OK Help!

If you had rust on battery terminals it is obvious that there is a lot more rust removing that has to be done. You neeed to go over every wire connection, fuse connection, etc and clean all out.

Sep 23, 2017 | Cars & Trucks

1 Answer

I have 2013 Chevy impala my vanity lights won't come on but the passenger side vanity lights work I changed the bulbs please help?

Talking about the sun visor lights?. There are small wires in them, pulling it up and down and left and right breaks these wires. To fix this you need to pull the visor(takes a special tool). Pop off the bezel at the roof mount the remove the screws to pull the mount out. Pull the wires until the plug comes out and unplug it. Then cut the stitching from the cloth/vinyl cover of the visor. Pull it out of your way. Find where the wire broken and repair it. Sew the visor back and re install. Visors aren't cheap. Last one I bought was $140.

May 12, 2015 | 2013 Chevrolet Impala

1 Answer

How to remove a sun visor in a 2015 jeep cherokee

unclip the sun visor from the "latch" side. Using a flathead pocket screwdriver gently pry the plastic shroud away around the hinge side. This will expose the bolts for the sun visor. Remove the weatherstripping partially from around the door if equipped with grab handles gently pry the covers off the hinges with pocket screwdriver and remove bolts (t30) partially remove cover from clip for sun visor and remove bolt (t20). Pull firmly directly out on a-pillar to unseat from pillar. Unscrew the three bolts from sun visor hinge side and gently unseat from wiring guide. Reaching above headliner gently guide wires for sun visor down through headliner and detach from harness.

Mar 05, 2015 | Jeep Cars & Trucks

1 Answer

How to remove the headliner

This YouTube site will give you all you need to replace headliner
Video for How to do I remove the headliner on a 2006 Chevy Silverado Sep 27, 2010 - Uploaded by
Replace your disintegrating GM headliner and Visors for less than ... With that being a GM ...

Nov 29, 2014 | 2006 Chevrolet Silverado

1 Answer

Installing a sun visor, right side. 2007 Hyundai, bought new. Right side visor wouldn't stay up, replace by dealer under warranty. Left side visor did same thing at 67000 miles, not covered. New...

There is usually a cosmetic cover hiding the two phillips head screws which attach the visor to the overhead. These covers 'clip' in place and can be removed using a small flat tip screwdriver. Once removed, you can then access these two phillips head screws. Remove the screws & gently remove the visor. You will find a wire harness connector to the visor. Find the release tab on the connector & press on it to disconnect the visor from the wire harness in the overhead. Installation is reverse of removel.
Go to and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, illustrations and procedures, etc.

Sep 02, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

How can i disable the light on my visor of my 1998 chevy suburban

To disable the light you will need to locate the hinge and fold down visor you will see three screws holding the visor on the roof, remove the screws and pull visor out, you will see the wire that powers the light in the visor, all you need to do is unplug the connector and reinstall the visor back on roof, good day,

Apr 10, 2011 | Chevrolet Suburban Cars & Trucks

1 Answer

How do I install sun visors in a 1994 Chevy Beretta? After I unscrew the three mounting screws, I can't find a way to remove the old sun visors. There appears to be no way to rotate the visor in a way...

What does you new visor ends look like that will replace the old ones. maybe they will give you an idea on whatyou can't see in the roof and help you understand which way they come out. Just a thought, Raz

Apr 20, 2010 | 1994 Chevrolet Beretta

2 Answers

How to remove the top for open effect

there are 4 bolts holding the 84 vette top on. two front two rear. There are holes in the top from the inside 2 behind the visors and two at rear. Wrench looks like an allen wrench. There is a tool for the removal which is usually stored in the glove compartment between the seats.

Apr 26, 2009 | 1984 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides