Question about 1988 Honda Prelude

1 Answer

1989 cv joint can i fix it?

I need to replace a cv joint on a 1989 honda accord i have alot of the tools and have done alot of repairs befor /.... is this something i should attempt?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 180 Answers

This should be a piece of cake for you.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove cv axel on 97' honda accord


Should be the same, as the model went from 94-97. I've done mine and the write-up looks good.
http://honda-tech.com/suspension-brakes-54/94-accord-removal-axle-2203243/

Oct 12, 2014 | 1997 Honda Accord

1 Answer

91 Honda accord when I turn left there is a knocking coming frm the front of my car


Sounds like a CV Joint to me. You could either buy the CV joint and replace it yourself, or take it in.

Oct 06, 2011 | 1991 Honda Accord

2 Answers

What problems will come with a 1990 Honda Accord with a passenger wheel turned in? Is it the axle? Should I purchase a car with this problem?


not really big problem on the axle they cost about $60 on the axle with exchanged labor will cost you about $80 to $100 its been worn out for about 80 to 150 miles when rubber cover loose or rip-off.

Feb 26, 2011 | 1990 Honda Accord

2 Answers

Need to replace a cv boot on a 97 accord.


replace the whole axle, they arent that much money, and you have to take it out anyway just to spend a bunch of time putting the boot on a axle with wear on that joint anyhow. ;)

Jan 27, 2011 | 1997 Honda Accord

2 Answers

My honda accord 1992 trasmission makes a bumpreaction when shifting from park to drive


With the hood open:

Put the car in park take off the emergency brake and push the car forward and back looking for a difference in movement of the CV joints where the Axle mates to the CV. I.e.... CV joint travels a short distance before you see any axle movement. Worn CV joint knuckles will cause all kinds of clunking.

If there is no movement between the CV joint and axle when you push the car fwd or back you already know the problem is internal to the transmission.

Kelly

Feb 25, 2010 | 1992 Honda Accord

1 Answer

How do i change the drivers side transaxle in a 1994 dodge carava


To change the CV axle, you have to remove the lower ball joint, remove the axle nut, remove from hub, (you can pull the strut out far enough to do this), and the axle will pull out. Install in reverse order. Sounds like you were trying to remove the transmission.

Jun 09, 2009 | 1994 Dodge Caravan

1 Answer

99 jeep gc need to replace cv joint


Not to bad you will need a ball joint spreader. some sockets wrench's.prybar.Remove the tire then loosen cv bolt. Remove brake caliber and bracket.re move ball joint nut.Remove steering rod nut.Get the ball joint spreader an remove steering rod then remove the ball-joint.Take the cv bolt off grab the strut and pull outward .With a rubber mallet knock cv out of housing.The remove from transmission.you my have pry a little.

Jan 16, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Replacing A wheel bearing


hi from the uk seriously the best advice i will give you having done these is remove wheel then with foot brake applied? remove the drive shaft securing nut(cv joint ) tap the joint back ? then remove b/caliper assy then diconnect track rod steering end then remove the bolt and nut that secures the lower ball swivel joint (you may find this stiff but percevier try a lever bar and press suspension lower arm down ) then two bolts and nuts secure hub assy to strut ? remove these and you can pull complete assy off drive cv shaft now you are best to take the hub assy complete with rotor/disc to a local engineer shop or garage that has a press or bearing puller hydraulic press is best option ? and ask if they could remove the old bearing and fit new for a small fee ? believe me these bearings can be a cow and if you want a quick turnround? this is best way rather than potential damage by trying to hammer bearing races out ? just a little more advice clean up/wash off assy before you take it to shop it will be more helpfull to mechanic to work on be sure you renew the cv hub nut and re torque after reassembly hope these instructions help you ? best wishes

Nov 11, 2008 | 2001 Honda Accord

Not finding what you are looking for?
1988 Honda Prelude Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...