Question about 1994 Oldsmobile Ninety Eight

1 Answer

Where would i go to fix a door that has a dent in it?

I stay in nacogdoches texas and i dont know where would be the nearest place to go

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Oldsmobile Master
  • 599 Answers

Sorry can't help,ask the locals who they use and see some of there work best i can advise. hope this helps

Posted on Apr 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dent in my car door


If the dent is not severe and the paint has not cracked around the edges of the dent then an accredited panel beater will be able to pull it back out using suction cups ( like those used to carry sheets of glass) If it is really bad but has not affected the door interior then the quickest and cheapest fix is to have a new door skin fitted. This is a panel beaters job and a door repaint. The last option is to get a door the same colour if possible from the wreckers and have it fitted .

Jul 01, 2014 | Cars & Trucks

1 Answer

Ford fiesta ajar light stays on and central lock not working


The central locking will not work when a door is open. find the door which is ajar and fix the door switch. Could be a stuck switch (either open or shut) May just need a whack with a soft faced hammer on the door frame. Don't hit it too hard you could dent the panels.

Nov 18, 2012 | Cars & Trucks

1 Answer

Hyundai elentra bent frame and door handle


No way to tell without looking at it and taking measurements.
It may be cheaper to replace the doors than to spend the time on repairs.

Sep 05, 2012 | 2010 Hyundai Elantra

1 Answer

How to remove dent out of the door


if the big is not real small, and covers a flat part of the door (with no moolded body lines), you can buy a suction body puller and it should work. also, try dry ice and sometimes, (if you hold your mouth right, lol) it will shrink the metal and the dent will pop out. be sure to wear gloves!! finially, you can buy a small spot welder,puller system. just weld the "tabs" on in strategic places, use the attached puller, and slide hammer the dents out. it takes practice, but it can be done.

May 06, 2012 | 2000 Chrysler Cirrus

1 Answer

Need to know if door panel can be removed to take out dents in door. I am female but not afarid of the work , do most minor repairs my self, cannot afford shop prices,,,,,need help,,,,,,thanks


This may sound ridiculous but have you tried a toilet plunger? Push in slow at dent, then pull out fast?
A quick stop or call to a local "Dent wizard" may surprise you. Sometimes relatively cheap and quick.
That said, yes door panel should come off. Search closely under and behind door handles etc., in out of the view places for any screws, as well as feel in any area probably near bottom where there may be carpet like fabric. Once you've got all you can find, pick a corner, or bottom, and give a quick pull to release any clips that are attached to back of panel. Once you start and have a section pulled out, you'll be able to see or feel where next one is holding. A good tool for popping those is available at parts stores. Looks Like a screwdriver at handle but has an angled double blade at end like a snakes tongue.motor1258_0.gif

Apr 06, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

I want to push out a dent in the rear plastic bumper but I have to take it off first.


Probably so. I have seen people use a round ended bar to push through the foam backing and force the dent back out. I have also seen someone use Insulating foam (used to seal around door & windows of houses) to spray into the dent. When the foam cures it expands thus pushing the dent out and providing new foam to help it stay there.

Feb 14, 2011 | Nissan Versa Cars & Trucks

1 Answer

Door was hit on a pole and bent almost straight out. Door closes and opens without any problem, but the top corner edge is bent and doesn't sit flush with the chrome trim or rear door trim. What might I do...


replace the door with a new unit,if money is a proplem, try a used one from junk yard should be cheeper than a new one jus have to get it to oa body shop to paint

Aug 24, 2009 | 2007 Volkswagen Passat Sedan

1 Answer

Fixing a rear door dent


if the dent is big enough.... just use a toilet plunger on the sheet metal (don't laugh it works). one the suction part is stuck to the door... pull hard to pull out the dent.

Apr 11, 2009 | 2001 Ford Escape

1 Answer

Window wont stay in track


its not impossible. you can do it. from my experience things get pretty tight when it comes to window tracks. you can't lose by trying though. good luck


please rate answer

Mar 21, 2009 | 1993 Ford F150 SuperCab

1 Answer

Need to take off driver side door panel to pound out dent


your best bet is either replace the door by going to a junk yard or go to a local autobody shop where they have the tools to fix the problem

Mar 13, 2009 | 1999 Honda Accord

Not finding what you are looking for?
1994 Oldsmobile Ninety Eight Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...