Question about 1998 Toyota Tacoma

1 Answer

Starter will not turn off, 1998 toyota tacoma

1998 Toyota Tacoma, 2.4L engine, auto trans., 2WD

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 141 Answers

Either the starter has failed or you have a bad ground. I would say starter.

Posted on Jan 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Temp sensor on 1998 toyota tacoma 3400


The engine coolant temperature sensor is usually located on the thermostat housing. This sensor controls the readings of the coolant temperature gauge in your vehicle when the ignition switch is ON .Here's a link to the sensor. REMOVAL & INSTALLATION

  1. Drain the coolant from the vehicle.
  2. Disconnect the engine wiring protector from the brackets.
  3. Disconnect the sensor wire.
  4. Using a 19mm deep socket, remove the sensor and gasket.
To install:
  1. Apply a thin coat of Loctite or equivalent to the switch. By hand, carefully thread the switch into the engine. If resistance is felt at all, remove the switch and inspect the threads for any damage. Continue to install the switch. Once installed, tighten to 14 ft. lbs. (20 Nm).
  2. Connect the sensor wiring.
  3. Install the engine wire protector to the brackets.
  4. Refill the coolant. Start the engine and check for leaks.
http://www.autozone.com/engine-management/coolant-temperature-sensor/duralast-coolant-temperature-sensor/toyota/tacoma-2wd/1998/6-cylinders-n-3-4l-efi-dohc/61401_0_18589

Aug 01, 2015 | 1998 Toyota Tacoma

1 Answer

Where is the camshaft position sensor on a 1996 toyota tacoma 2.7 located.


Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

Oct 14, 2014 | 1996 Toyota Tacoma

1 Answer

Toyota Tacoma fuel problem


Check the following:
- Listen to the fuel pump noise under the fuel tank.
- Starter signal.
- EFI relay, under the hood fuse and relay box.
- Fuel pump operation and pressure.
- Regulating valve.
- Circuit Opening Relay (COR) under the dash.
- Check for open in harness and connector between circuit opening relay and fuel pump, and fuel pump and body ground

83744154-13d8-40aa-bba8-aac743062e3f.png
98828e43-1df3-476c-94fa-036164d23c8e.png

2e76aaa2-2dec-411f-a493-b4d0f142f0f8.png
Hope that works. Thank you for visiting Fixya.

Mar 18, 2014 | 1998 Toyota Tacoma

1 Answer

I have a 1998 toyota tacoma and have successfully removed starter from engine but cant remove it from engine compartment


Hi,
You can remove it by way of going under the engine or your car.
Hope that solve your predicament!

Dec 08, 2010 | 1998 Toyota Tacoma

2 Answers

I have a 2006 toyota tacoma 4dr prerunner sr5 v6 long bed WITH towing package- is 750 ccas too much? or should i say rated for this truck?


750 is fine but from a professional view, you should always replace with what the manufacturer recomends

Nov 03, 2009 | 1998 Toyota Tacoma

1 Answer

Tacoma won't start, or shift out of park.


Try putting foot on brake, or is key in ignition, also over-ride button by shifter. Auto's have safety micro switches in these places so not to have car in drive and start, "extremely dangerous" Try this first easily missed. lol

Mar 08, 2009 | 2005 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

68032 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...