Question about 1999 Chevrolet Silverado 1500

1 Answer

Oil Pressue Switch

Location of oil pressure switch on a 1999 4.8 chevtolet truck

Posted by on

  • mjpottinger Jan 12, 2009

    Thank You, It was exactly were you said it was. What a great help. Mike.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

IT IS at back of engine behind intake. in the valley right were tranny bolts up. if you have a thin wall oil sender socket you can get it out with a extension.

Posted on Jan 09, 2009

  • TripleTauto
    TripleTauto Jan 12, 2009

    thanks for the fixya rating

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pressure switch 1999 dodge ram 1500 5.2 location


Hello Dave,

Your oil pressure switch is located at the back of the engine, next to the distributor.

May 30, 2016 | Dodge Cars & Trucks

1 Answer

Where is the location of the oil pressure switch on a 1999 mits eclipse ?


The sensor to the oil pressure gauge is the large dome shaped sensor adjacent to the oil filter. The sensor to the oil light is in front of the dome shaped one both have one wire coming from them

Mar 18, 2015 | 1999 Mitsubishi Eclipse

1 Answer

I have a bad oil leak on my 1996 Plymouth Breeze. I was told it was the oil pressure sender and needed a special socket, and was located on the block below the exhaust manifold. I was sold the socket and...


ok i believe the one you changed is the switch the one next to it is the oil pressure sending unit
there is a difference between the two///// make sure they sell you thread tape so this way you don't have any leaks//// it doesn't take a lot of thread tape on the threads


hope this helps you
good luck
bob

May 11, 2011 | 1996 Plymouth Breeze

1 Answer

I need to know where the oil sending gauge is in a 1993 ford f250


Oil pressure switch location - 4.9L engine

tecnovative_92.gif
Oil pressure switch location - 5.0L/5.8L engines

tecnovative_93.gif
Oil pressure switch - 7.3L diesel and 7.5L gasoline engines (adapter is for 7.3L only)

tecnovative_94.gif

Feb 04, 2011 | Ford F-250 Cars & Trucks

1 Answer

I need to know where the oli sending unit is and how to replace it?


zjlimited_305.jpg

Fig. 1: Location of the oil pressure switch-3.3L and 3.8L engines


zjlimited_306.jpg

Fig. 2: Location of the oil pressure switch-3.0L engine


zjlimited_307.jpg

Fig.: Oil pressure switch (sending unit) schematic


The low oil pressure warning lamp will illuminate when the ignition switch is turned to the ON position without the engine running. The lamp also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:

  1. Turn the ignition switch to the ON position.
  2. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
  3. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
  4. With the ignition switch turned to the ON position, check the warning lamp. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.

REMOVAL & INSTALLATION
On the 2.4L engine, the oil pressure switch is located on the side of the engine block facing the firewall. On the 3.0L engine, the oil pressure switch is located on the oil filter adapter housing, next to the starter motor. On the 3.3L and 3.8L engines, the oil pressure switch is located next to the oil filter.
  1. Locate the oil pressure sending unit on the engine.
  2. Disconnect the negative battery cable.
  3. Disconnect the pressure switch electrical harness.
  4. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the pressure switch from the engine.
To install:
  1. Install the pressure switch into the engine and tighten securely.
  2. Attach the electrical connector to the switch.
  3. Connect the negative battery cable.
  4. Start the engine, allow it to reach operating temperature and check for leaks.
  5. Check for proper oil pressure switch operation.

Hope this helps (remember to rate this answerr).



Dec 22, 2010 | 1999 Plymouth Voyager

2 Answers

Oil pressure switch location on 1999 chev cavalier


The oil pressure switch relays the oil pressure in the engine to the instrument cluster. The switch will illuminate the OIL PRESSURE light if the oil pressure drops below 2psi (13 pa). The switch is usually located on the side of the engine, under the intake manifold on the 2.2L engine and on the side of the intake camshaft housing on the 2.3L/2.4L engine.


7fef8ab.jpg

Fig. 1: The oil pressure switch is located on the engine block under the intake manifold and is accessible from underneath the vehicle-2.2L engine

bdee34a.jpg

Fig. 2: Oil pressure switch location-2.3L/2.4L engine


Other, the low oil level switch activates the OIL light in the instrument cluster when the oil level in the pan goes below a certain level. The switch is mounted on the oil pan.


Hope this helped (remember rated this post).

Apr 11, 2010 | 1999 Chevrolet Cavalier

1 Answer

1993 chevy truck 4.3 oil pressure high to low


It may be a coincidence but try replacing the oil pressure-sending unit if it does not change try changing back to the original oil

Aug 30, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Changed oil pressure switch,still no oil pressure


The fuel pump on that model runs through the oil pressure switch so that if the truck looses oil pressure,It kills power to the fuel pump to prevent engine damage.you need to find the cause of the low oil pressure reading(possibly a bad oil switch).That would be the cheapest place to start,or have it checked with a mechanical gauge.Good luck,
ChevRev

Mar 30, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Head not oiling


check oil pressue . sound like oil pump . if oil pump is good .your oil distribution passages is stop up with sludge.

Mar 22, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...