Question about 2002 Nissan Altima

1 Answer

Can not remove rear wiper arm from the wiper motor shaft.

The broken wiper arm seems to fitted on a cone shaped shaft. After the locking nut has been removed and despite heavy spraying with releasing oil, it resists all efforts to lever it off. Indeed it lifts the motor shaft slightly through the bodywork. Is a special tool like a drawer required, or am I missing seeing some other fastening device?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 6,674 Answers

Try prying up on 2 edges at same time, and wiggle it. If that doesn't work, spin nut back on to cover threads but leave loose enough for a little movement while you pry in 2 spots across from each other & have someone tap the center shaft & nut, with a quick rap of hammer. Not too hard.

Posted on Jan 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Remove rear wiper arm 1998 v70


http://www.volvo-forums.com/t36992-rear-wiper-arm-v70.htm

May 10, 2014 | 1998 Volvo V70

1 Answer

I need to remove the rear wiper arm from a 2007 Pontiac Torrent. I have removed the nut, but I can't seem to get the arm off of the motor shaft. Any tips??? I am trying to change out the rear wiper...


a small puller is best, but if you use a penetrating oil on the shaft, and a couple of screwdrivers (use rags underneath so you do not damage paint) you can walk it off the shaft.

Aug 07, 2011 | Pontiac Torrent Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

I remove the wiper arm & the outsdie lock of the shaft,remove the screws that hold the wiper motor inside, to I need to remove the 20mm nuts that hold the rubber seal outside the glass (in which I can...


IF YOU TALKING ABOUT REAR WIPER MOTOR REMOVAL YOU HAVE TO REMOVE PULL THE REAR WIPER ARM COVER BACK TO ACCESS THE WIPER ARM RETAINING NUT.DETACH THE NUT AND PULL WIPER ARM STRAIGHT OFF THE SHAFT TO REMOVE IT.

Nov 26, 2010 | 2000 Honda Odyssey

1 Answer

Wipers will not move, makes noise and there is power to the motor. Motor was replaced. Someone told me that the arms probably moved to far and are now stuck, how do I fix this?


Windshield Wiper Blade & Arm Removal & Installation Front To Remove:
  1. Mark the location of the wiper on the windshield.
  2. Remove or disconnect the following:
    • Nut cover
    • Nut from the wiper arm
    • Wiper arm
Wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt.gif
To Install:
  1. Install or connect the following:
    • Secure the wiper arm with the nut.
      1. Tighten to: 17 ft-lb (23 Nm)
    • Nut cover
Rear To Remove:
  1. Put the wiper arm in the park position.
  2. Remove or disconnect the following:
    • The washer hose from the connector
    • The cap from the wiper arm
    • The nut from the wiper arm
    • The wiper arm from the wiper motor shaft
Rear wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt_rr.gif
To Install:
  1. Install or connect the following:
    • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
    • The nut on the wiper arm
      1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
    • The cap on the wiper arm
    • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

Oct 08, 2010 | 1997 Chevrolet Blazer

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

1 Answer

Replace the rear wiper arm shaft


There is a plastic cover that pops off at the pivot end of the wiper arm. pulling up on this with a hook of some kind from the furthest end should release it. Under it you will find a nut that holds the wiper arm to the shaft. It's quite common for the nut to come loose and the shaft spins without moving the arm. Try tightening this nut (with the ignition on, be sure the wiper motor is off, then turn off ignition and put the wiper arm in the parked position). This is a common problem if you've ever tried to turn on the wiper when it was frozen to the glass.

Feb 26, 2010 | 2000 Honda Odyssey

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

2 Answers

Rear wiper linkge BMWe46 touring 2003 year


Not sure about this exact car but 99% of all wiper motors are retained with a nut ythart lives under the base of the wiper arm and with three or 4 nuts from the rear of the motor. Take the wiper arm off, possibly requiring the use of a 10 mm wrench, and you will see a large nut, remove this. See if the wioper mote is accessed from the trunk, most likly under a clip in panal, split the electrical connector and remove the nuts holding the motor on. You will see that the collar that had the nut accessed from above will be stiff to move on the wiper shaft. Work it off, scotch brite the shaft, run a small wire brush down the typically plastic tube, lube the shaft with chassis grease or white grease, check that it moves freely in the collar and reassemble

good luck

Feb 06, 2009 | 1999 BMW 318 ti

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2002 Nissan Altima Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...