Question about 1993 Dodge Dakota

2 Answers

1993 dodge dakota installed new fuel pump and checked all fuses

After all of this i still cannot get pump to engaga

Posted by on

  • getthechad May 11, 2010

    where is the shutoff inertia switch?



2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

Check the shutoff inertia switch. The pump relay/fuse or it could be a bad pump circuit.It could be any of these. Make sure the gas cap is tight. fuel pressure must be good for the pump to work.

Posted on Jan 09, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is inertia. Switch

Posted on Apr 23, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1993 5.2l 4x4 dodge dakota. No spark no fuel

ASD relay ! Is there B+ voltage to the coil's ? Fuel pump relay electrical circuit diagnostic's . Do you have an know how to test with a DVOM digital volt ohm meter ? You can check out wiring diagrams at ! The ASD - auto shut down relay power's up the fuel pump relay , ignition system an some other thing's . It's in the under hood fuse box !

Sep 06, 2016 | 1993 Dodge Dakota

1 Answer

Will fire ,but will not turn over

Dodge Dakota Crank No Start Fix - YouTube

? 8:10
Jun 29, 2014 - Uploaded by AJ Pierce
In this video, I will show you how I fixed my 1992 Dodge Dakotanot starting. ... Engine cranks but won't start - Duration: 18:30. jimthecarguy ...

Inspect Fuses if Engine Cranks But Does Not Start : Dodge ... > Problems > Dodge > Dakota
Engine Will Not Start Due to Blown Door Lock Fuse on Dodge Dakota ... cap and rotor, wires, plugs, coil, fuel pump assy, coil pickup sensor, crank position sensor and have new ECM on the way, Cranks but won't fire. ... 1990 Dodge Dakota.

Dakota won't Start - Discussion on Topix > Dodge Dakota
Jan 22, 2009 - have a 1993 dodge dakota sport that wont start. when you turn the key on there is no power to the fuel pump and does not fire. any ideas ... I just bought a1990 Dodge Dakota Sport 4x4 5-Speed, there is only one problem, it only .... I went to move it the other day, it would turn over, but had no spark or gas.

Dodge Dakota Questions - PROBLEM STARTING - CarGurus > Questions > Dodge > Dakota


Jan 09, 2016 | 1990 Dodge Dakota

1 Answer

Do you have to drop the engine to replace oil pump in 2007 gmc yukon

You have to remove the engine front cover (over timing chain) and remove the oil pan to get the oil pump in and out. You don't have to remove the heads, however.

Removal & Installation

4.8L, 5.3L, 6.0L & 6.2L Engines

Fig. Exploded view of the oil pump mounting-4.8L, 5.3L, 6.0L and 6.2L engines

Fig. Oil pump disassembly-4.8L, 5.3L, 6.0L and 6.2L engines

  1. Remove or disconnect the following:


    Do not allow dirt or debris to enter the oil pump assembly, cap ends as necessary.


    The internal parts of the oil pump assembly are not serviced separately (excluding the spring). If the oil pump components are worn or damaged, replace the oil pump as an assembly. Do not attempt to repair the wire mesh portion of the pump and screen assembly.

    Engine front cover Oil pan Oil pump screen bolt and nuts Oil pump screen with O-ring seal. O-ring seal from the pump screen. Discard the O-ring seal. Remaining crankshaft oil deflector nuts. Crankshaft oil deflector Oil pump bolts

    Oil pump To install:


    Inspect the oil pump and engine block oil gallery passages. These surfaces must be clear and free of debris or restrictions.

    1. Align the splined surfaces of the crankshaft sprocket and the oil pump drive gear and install the oil pump. Install the oil pump onto the crankshaft sprocket until the pump housing contacts the face of the engine block.

    2. Install or connect the following:


      Lubricate a NEW oil pump screen O-ring seal with clean engine oil.


      Push the oil pump screen tube completely into the oil pump prior to tightening the bolt. Do not allow the bolt to pull the tube into the pump.

      Oil pump bolts. Tighten the oil pump bolts to 18 ft. lbs. (25 Nm). Crankshaft oil deflector

      NEW O-ring seal onto the oil pump screen

    3. Align the oil pump screen mounting brackets with the correct crankshaft bearing cap studs.

    4. Install or connect the following:

      Oil pump screen Oil pump screen bolt and the deflector nuts. Tighten the bolt to 106 inch lbs. (12 Nm) and the nuts to 18 ft. lbs. (25 Nm). Oil pan Engine front cover

Mar 06, 2015 | GMC Cars & Trucks

1 Answer

Replace water pump torrent

drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

No fuel pressure on 1993 Dodge Dakota, How do I check the fuel pump? I cannot hear it run.

If you cannot hear the fuel pump prime up when you turn the key to on there is a fault with your fuel pump. check the fuse in the fuse relay box and the 2 wired connections on the fuel pump, if still no good than replace the fuel pump

Oct 09, 2012 | 1993 Dodge Dakota

1 Answer

Changing the in tank fuel pump

you have to drop the tank out of the truck first empty all the gas then drop it out and pull out the old fuel pump and replace it with the new one put back into the truck put some gas in and your done

Sep 28, 2012 | 1993 Dodge Dakota

1 Answer

Water pump

Which engine?

  1. Drain the radiator


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.

  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    Could there be no fuel getting through the carb because of a fuse being blown

    yes if the fuel pump is electric but if not it will be a mechanical pump and if so i would recomend replaceing the pump but if electric check all fuses and relays

    May 07, 2012 | 1993 Dodge Dakota

    1 Answer

    Change the water pump

    • Tools Required
    • J 43651 Water Pump Holding Tool
    • Remove the thermostat housing.
    • Remove the water pump access plate from the front cover.
    • Remove the right hand fender liner.
      1. Important: A drain plug has been provided at the bottom of the water pump assembly for additional coolant drainage from the engine block and water pump.
      Drain the coolant from the water pump using the plug at the bottom of the pump.
      1. mportant: The water pump holding tool supports the sprocket and chain during water pump service. The tool must be used or the balance shaft must be re-timed.
      Install the J 43651 into position.
      1. Tighten the bolts on the water pump holding tool into the threads on the water pump sprocket.
      2. Install the access cover bolts that were removed earlier to secure the water pump holding tool to the front cover assembly.
      3. Remove the 3 inner water pump sprocket to water pump blots.
        1. Important: Be sure to remove both water pump bolts from the front of the engine block.
        Remove the 2 water pump bolts.
        Remove the rear 2 water pump bolts.
        1. Remove the water pump.
        2. Remove and discard the water pump O-ring seal.
        Installation Procedure
        1. Important: Prior to installing the water pump, read the entire procedure. This will help avoid balance shaft chain re-timing and ensure proper sealing.
        Install a NEW water pump O-ring seal.

        1. Important: A guide pin can be created to aid in water pump alignment. Use a M 6 m x 6 mm stud. Thread the pin into the water pump sprocket.
        Using the guide pin, align the pin with the water pump holding tool.
        1. Position the water pump against the engine block and hand tighten the water pump bolts.
        2. Notice: Refer to Fastener Notice.
        Install the inner water pump sprocket bolts. After 2 are snug, remove the guide pin and install the 3rd bolt.
        Tighten the bolts to 25 Nm (18 ft. lbs.).
        1. Tighten the water pump sprocket bolts last. Tighten the bolts to 10 Nm (89 inch lbs.).
        2. Remove the J 43651.
        3. Install the water pump access plate and bolts. Tighten the bolts to 10 Nm (89 inch lbs.).
        4. Install the right hand fender liner.
        5. Install the thermostat housing.

    Aug 29, 2011 | 2006 Pontiac Solstice

    Not finding what you are looking for?

    Open Questions:

    See all 1993 Dodge Dakota Questions

    1993 Dodge Dakota Logo

    Related Topics:

    449 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts


    Level 3 Expert

    77947 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides