Question about 2003 Ford Explorer

1 Answer

1999 Ford Explorer Rear Windshield Wiper

My 1999 Explorer's rear windshield wiper does not wipe the entire window, it only gets the very end. I have tried changing the wiper blade and bending it towards the window for more grip. No success! Any suggestions? Thanks ~C

Posted by on

  • Adam Baker
    Adam Baker May 11, 2010

    Hi, my name is adam. I am pretty sure by what you are describing is the same problem I have had. Is the blade that you have on there a winter wiper blade? If so, a ford explorer's back window is an awkward shape and regular blades do the best.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

You can unbolt the wiper arm and change to where you think it should be then bolt it back up /Please rate my response thank you very mudh

Posted on Jan 31, 2009

1 Suggested Answer

michigan man
  • 3533 Answers

SOURCE: 1999 Ford Explorer Rear Windshield Wiper

may have to replace the entire arm assembly as the tensioner spring in the wiper itself is worn

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What type of fuse is used for a 2007 Eddie Bauer Ford Explorer rear windshield wipers and where is it placed?


Your owners manual will give you fuse location and identification for the rear wiper. Most likely a wiper motor problem though. Turn on rear wiper and grab rear wiper arm and see if it will move at all. If it does move a bit or starts working....the motor is the problem

May 01, 2015 | 2007 Ford Explorer Eddie Bauer

3 Answers

1999 ford explorer rear wiper don't work


hi there
this is pretty typicalof rear wipers check fuse first to make sure it is good if that doesnt work it is probably the motor which goes out and you can pick one up at your local auto parts store hope this will help you and have a great day

Aug 21, 2011 | 1999 Ford Explorer

1 Answer

Why won't my Windshield wiper on back window stop? I need to know which fuse would operate the back window windshield wiper.


the rear wiper fuse locate at the interior fuse panel, #5 15A, if the fuse is ok, check the circuit braker 4.5 A,

Jul 24, 2010 | 1992 Ford Explorer

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Rear windshield wiper problem on 99 Expedition.


2 ways of dealing with this. Install a new motor or put up with it until you install a new motor. I usually give it a very light tap with a hammer or a wrench & they start working fine at least for a while

Oct 15, 2009 | 1999 Ford Expedition

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

1 Answer

1999 Ford Explorer Rear Windshield Wiper


I usually fix this by bending the arm as low as possible to the base part just make sure the arm doesnt hit the glass handle when it sweeps

Feb 28, 2009 | 1999 Ford Explorer

1 Answer

Rear windshield wiper


Try tightening the bolt that holds the wiper in place. There is a cap over it at the base of the wiper where it attaches to the window pop that cap and you will see the it.

Jan 23, 2009 | 1999 Chevrolet Suburban

1 Answer

1999 Ford Explorer Rear Windshield Wiper


may have to replace the entire arm assembly as the tensioner spring in the wiper itself is worn

Jan 14, 2009 | 1999 Ford Explorer

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2003 Ford Explorer Logo

533 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...