Question about Ford E-250

1 Answer

390 ford distributor internal assembly replacement

I need to replace the internals of a 390 1976 ford distributor. I purchased the assembly but can seem to see how to get the gear off inorder to put in the new assembly

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

There is a roll pin on the gear. Take a small punch and knock it out. When you get the pin knocked out, spray carb. cleaner around the gear and shaft and with a rag wrapped around the gear to keep from cutting your hand, turn the gear while holding the rotor. It will come out and you can pull the shaft up through the distributor.

Posted on Jan 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a distributor for a 1974 ford 390 can,t get pickup to time right


did you try getting number 1 up and see where the tim
ing mark is

Oct 24, 2015 | Ford Cars & Trucks

1 Answer

Won't start after ignition switch is released


One of your wires is on the wrong side of the starter solenoid. You need to get a test light and figure out which wire goes to the coil and trace it back to the solenoid, switch it from the starter post to the ignition post and you should be good.

Jul 14, 2014 | 2005 Ford F-150 SuperCab

1 Answer

The distributor on my husbands 99 Nissan Quest stopped turning. I'm guessing that it is broken. Is this expensive to replace


most likely timing belt failed.this turns camshafts which in turn rotate distributor.fotunately for you ford insisted nissan make this a non interference engine during their joint venture with mercury villager.so no internal damage should have occurred.im guessing about 700.00 to replace timing belt,water pump and drive belts.

Jan 16, 2011 | 1999 Nissan Quest

1 Answer

390 ford engine will not idle when in gear. how do i tell if it has burnt valves 1976 ford pick up f100 automatic


you need to do a compression test and a leakdown test. Both take special tools and you will need an air compressor for the leakdown tool.

Feb 21, 2010 | Ford F-100 Cars & Trucks

1 Answer

Firing order diagram for a 1976 ford f150


V8 351 351W 400 -FIRING ORDER IS 1 3 7 2 6 5 4 8 THEN YOU HAVE V8 302 330 359 360 361 389 390 401 460 475 477 534 FIRING ORDER IS 1 5 4 2 6 3 7 8. THIS IS YOUR FIRING ORDERS FORD HAD MANY V8 ENGINES.I PUT THEM ALL DOWN.YOU DID NOT TELL ME YOUR ENGINE SIZE.

Sep 25, 2009 | Ford F-150 Cars & Trucks

1 Answer

1990 HONDA ACCORD DISTRIBUTOR LEAKING OIL INTERNALLY


Lease check and make sure that you replace with the right seal, that alone should have taken care of this problem. However if the valve cover gasket is loose or bad it will cause oil to leak around distributor are but NOT into distributor. This seal can be easily replaced by loosing 4 10mm bolts on top of valve cover. Contact if you need more help Good luck and thanks for using FIX YA

Mar 26, 2009 | 1990 Honda Accord

1 Answer

1996 f 150 is not cranking. It is turning over but there is no fuel getting to the engine. I have replaced everything.


3 easy and quick steps first, check fuel pump, fuel regulator,and distributor module, and also the internal distributor , should have blades that pass module for fuel injectors and or pump.

Dec 27, 2008 | 1996 Ford F150 Regular Cab

1 Answer

1976 ford f-100 (390) 4-barrell


About 36 degrees.Hope this helps

Oct 19, 2008 | 1981 Ford F 100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...