Question about 1985 Chevrolet Citation

Open Question

Need wiring diagram for 1984 chey citation x11 steering collom

I am trying to use a steering collom out of a 1984 chevy citation x11 for a kit car. I need to figure out witch wires on the plug goes to were??
Turn signals, horn, wipers, high beems ect.

Thank You

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 78267 Answers

SOURCE: plug wire diagram

This was all I could come with, hope it helps.


Posted on Sep 16, 2008

  • 32 Answers

SOURCE: wiring diagram

Helpful Wiring Information when hard wiring your brake control:
Run two wires to the battery:
White - Ground
Black - Power
Blue - Run to Electric Brakes at the Rear Plug
Red - Run to cold side of brake switch off of the brake pedal (using a test light to find the cold side)
Note: Always wire the red wire to the heaviest gauge wire when testing cold side of brake switch.

You can view more info here.

Posted on Nov 17, 2008

  • 226 Answers

SOURCE: timing on a 350 chey engine

take out number 1 spark plug and put your finger as to block the hole ,have a friend bump the starter till you feel air rush out real fast / called the compression stroke when it does stop and look down the top center for timing marks on the pulley and line them up on the timing cover then place the distributor in place as so the rotor is pointing at the #1 piston location, basically the dr. front corner and start there, timing order is 1..8..4..3..6..5..7..2.. now if you get all these in right 1..3..5..7 are on the drivers side front to back and 2..4..6..8 on the passengers bank front to back and the distributor turns clockwise .good luck hope this helps you.

Posted on Jan 02, 2009

  • 10 Answers

SOURCE: where is the horn located on a 1984 Chevrolet

drivers side of car way down low

Posted on Oct 29, 2009

  • 2984 Answers

SOURCE: spark plug wiring diagram for 98 tahoe

You didn't post your engine size so please pick the applicable diagram:

1996-98 4.3L Engines Firing Order: 1-6-5-4-3-2Distributor Rotation: Clockwise

1996-98 5.0L, 5.7L and 7.4L Engines Firing Order: 1-8-4-3-6-5-7-2Distributor Rotation: Clockwise

4.3L Engines Firing order: 1-6-5-4-3-2 Distributor rotation: Clockwise

4.8L, 5.3L and 6.0L Engines Firing order: 1-8-7-2-6-5-4-3 Distributorless ignition system (one coil on each cylinder)

5.0L, 5.7L and 7.4L Engines Firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets

Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

Belt routing diagram for 1984 Chevy G20 van 5.0 with multiple belts

first is alternator/ water pump/ crank... second is power steering and smog if equipted.. last is ac compressor..

Feb 24, 2013 | Cars & Trucks

1 Answer

My 1984 chevy citation 2i died in the middle of the road...4 cylinder model.... its not spraying fuel and not getting spark the fuel filter is good fuel is getting to the injector but not spraying..... i...

Are you getting power to the coil ?
It could be the stator-pickup in the distributor or a lack of voltage to the ignition system.
Is the check engine light on when you turn the key on ?

Aug 01, 2012 | 1984 Chevrolet Citation

1 Answer

Wiring diagram for distributor on 1984 chevy k10 1/2 ton

i need a diagram for putting back together a steering column in a 1984 chevy

Jan 15, 2012 | Cars & Trucks

1 Answer

Need to see wiring diagram for chevy

Go to google and type in 1984 Chevy K1500 wire diagram and one should come up.

Jun 30, 2010 | 1984 Chevrolet K1500

1 Answer

Just got truck painted, need wiring diagram to get

Haynes repair manuals would have good wiring diagrams. Or google it, you can find about everything on the internet, but sometimes a problem with too small of print, or maybe my computer skills need sharpening.
I don't know about those wire connections not plugged in. Are you sure they are from the doors? Can't imagine what they would be.

Jan 27, 2018 | 1984 Chevrolet S-10

2 Answers

I have a 1984 chevy citation 2 i need to replace that starter. but don't want to pay a mecanic to do it. how do you take the old one out? it is a 6 cilinder.

If you have fuel injection you need to de-pressurize the system first. To do this remove the fuel pump fuse from the fuse panel. Start the engine and let it run until it quits. Then crank the engine an additional 3 to 5 seconds. Turn off the key and re-install the fuse.
Jack the car up and block it so you can get under it. Disconnect the battery ground and put it well out of the way. Remove the wires from the solenoid. When you do pay close attention to where they go, label them or maybe make a diagram showing you which color goes where. You'll be glad you did when it is time to put it back together. Remove the support mounting bracket bolts. If there is a heat shield over the solenoid detach the bracket from the starter. Make sure the front support bracket is loose on the motor so it will swing out of the way. Remove the 2 bolts from the bottom of the starter and it should come out. If there are shims there when you take it out, they will have to go back in with the new starter.
If fuel lines are in the way when you try to drop the starter, undo the retaining clamp and loosen them off at the regulator so you can move them to one side.
To install the new starter is just the reverse. Be sure to use a new solenoid with a new starter.Hope this helps.

Mar 01, 2010 | 1984 Chevrolet Citation

1 Answer

Ignition switch wont come out how to take the steering collom off

you need a steering wheel puller, dont use a hammer!

Jul 18, 2009 | 1984 Ford F 150

2 Answers

Nned steerin column diagram

I don't have a diagram, But I have taken tons of these apart. Is there something I can help with?

May 04, 2009 | 1984 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides