Question about 1994 Pontiac Bonneville

1 Answer

Tension Pully is broke need to remove

I need to no how to remove the tension pully off of a 1994 Pontiac boniville

Posted by on

  • Anonymous Mar 23, 2014

    broke tension pully



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 196 Answers

Well i take it the belt is off allready teh should only be one bolt 15mm if i remember right remove this bolt and the tensioner should come off.

Posted on Jan 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have a 2000 chevy malibu. Serpentine belt broke. can you put it on easily by moving tension bar?

yes, follow the diagram under the hood. get it threaded right then move the tension pully to allow it to get on the last pully and your done.

Oct 08, 2010 | 2000 Chevrolet Malibu

2 Answers

Need to know how to adjust serpentine belt, please show diagram. 6 cyl engine.

Really don't need a diagram. Loosen the slide bolts on the power steering pump. loosen or tighten the pump by turning the jack screw (long transverse bolt) under the pump. Once the belt is tightened up, lock down the slide bolts and you are finished.

Jun 17, 2010 | 1994 Jeep Grand Cherokee

1 Answer

1994 ford econline serpitin belt brok and tension pully broke off can i get just the pully put on

Yes the tensioner pulley and bearing assembly can be purchased and installed.

Dec 31, 2009 | 1985 Ford Econoline

1 Answer

How do you change a tension system on a 1999 chrysler town and country the engine is a 3.8

if your set to do it. First you have to dismantle the front of the motor. then unload the tension pully. unbolt the water pully the steering pump. then the tensioner. replace here's where it get hard in the small space you'll have to put tension on the ten to put belt back on. broke hand here.

Dec 06, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

Cant find the tension pulley

It is the pully just behing the alternator pully. Take a box end wrench put it on the pully bolt head and turn it to release pully tension.

Oct 31, 2009 | 1997 Pontiac Sunfire

1 Answer

Serpentine Belt Alignment

you shouldnt have any allignment issues, assuming that the pully is good. if it needed to be replaced, you would know it. you would hear all kinds of odd noises...but my guess is that when the tension was put back on the belt, it was overlapping one of the edges on a pully farther down. just take a close look at where the belt is routed, and make sure that it is on its track on every pully. if not, release the tension, reallign, and tighten up again.

Aug 04, 2009 | 1997 Pontiac Grand Prix

2 Answers

How do you adjust tension for drive belt

first you need to figure out if you have an automatic tensioner or an adjustable one. so look at the pullies which ones are not accesories (ie not an alternator pully, power steering.) some pullies will just be on there own not driving anything. is this pully connected to something like this O>o <--this end is the pully.
pully mounting bolt ^ ^arm with hole for rachet
or does it look like the pully is attached to a threaded pole.

the auto adjuster need a rachet to pull back on it (because it's spring loaded) while you install the new belt.

the other need the nut on the pully loosened and the threaded pole loosened will move the pully removing tension from the belt (opposite will tension the new belt).

tighten belt until you can only twist it in half.

Jun 25, 2009 | 2003 Toyota Camry

1 Answer

Need to change pully

Which One?
60a96c9.jpg The one on the left has two 14mm fasteners 1 nut & 1 bolt. The one on the right has the same 1 14mm nut and 1 14mm bolt. Both are simple to replace. Step 1: Relieve the tension on the pully you wish to replace. Step 2: remove the pully (front) by removing the 14mm nut. To remove the rear tensioner pully, remove both nut & bolt.

May 19, 2009 | Hyundai Motor 2005 XG350

1 Answer

I am trying to replace the serpentine belt on my 1994 Ford Tbird LX. How do I remove the tension to allow me to remove the old belt?

You need to find the idler tension pully. This moves up and down with the aid of a large spring. Placing a large wrench on the nut in the middle of the tension pully, you will be able to move it up or down to release the belt and install it.

Nov 27, 2008 | Ford Thunderbird Cars & Trucks

2 Answers

Changing Serpentine Belt

That bolt keeps the belt tensioner on. There are two bolts on a typcial tensioner. One to keep the pully on, the other to keep the whole asembly on. Since it's a GM, you should either see a square hole, around 3/8 in or a raised slot. You can put a 3/8 braker bar in the hole and you push it to remove the tension. No need to remove any bolts. Or, there could be a slot sticking out on it, you can put a wrench on it and push it to remove tension. When there is no tension, you slip off the belt from any pully, i prefeer slipping it off a top pully for easier access, and same for instaliton. Set the new bet up the way your old one was exepct for the highest pulley, remove the tension from tensioner, slip belt back on last pully and let the tensioner do it's job. If you remove the bolt that keeps the tensioner on, it will pop off and easily hurt yourself. After the new belt is on, make sure it is on correctly. There are small ribs on the inside of the belt, if those aren't in the groves properly of all the pullies, the belt will not last as long.

Sep 06, 2008 | 2005 Chevrolet Colorado

Not finding what you are looking for?
1994 Pontiac Bonneville Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides