Question about 2002 GMC Envoy

2 Answers

How to tell if my GMC has keyless entry - 2002 GMC Envoy

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Call your local dealer and give the parts person your VIN # located on the dash on the drivers side and they will be able to tell you what your vehicle was equipped with.

Posted on Jan 08, 2009

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

Close all doors put key in hold unlock down on drivers door turne on and off 2 times while holding un lock down if doors lock and horn blows you have the system .

Posted on Apr 05, 2009

3 Suggested Answers

n_c_713
  • 20 Answers

SOURCE: I'm looking for instructions on how to program the keyless remote

HOLD TO UNLOCK BUTTON ON YOUR DRIVERS DOOR, WHILE HOLDING BUTTON DOWN TURN KEY ON, OFF, ON OFF, ON OFF, YOUR DOOR LOCKS SHOULD CYCLE,. LET GO OF THE UNLOCK BUTTON. HOLD DOWN LOCK AND UNLOCK BUTTONS ON YOUR REMOTE AT THE SAME. IT WILL TAKE ABOUT 1 MIN AND YOUR DOOR LOCKS WILL CYCLE AGAIN. IF YOU HAVE MORE THAN ONE REMOTE, HOLD DOWN LOCK AND UNLOCK ON THAT REMOTE AFTER FIRST REMOTE IS PROGRAMMED. ONE AT A TIME. TURN VEHICLE ON AND TURN BACK OFF. YOUR REMOTES SHOULD WORK. GOOD PLACE TO HOLD YOUR REMOTES IS CLOSE TO IGN. CYLINDER SWITCH

Posted on May 05, 2009

  • 59 Answers

SOURCE: does truck have keyless entry installed by factory

Write down the VIN# and take it to the dealer. They would be able to tell you if it did or didn't come with factory keyless entry.

Posted on Sep 07, 2009

tpavlik
  • 2 Answers

SOURCE: Keyless entry not working on

my remote start ont work but door locks work 2007 buick

Posted on Jan 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost my keyless entry for my 1999 Saturn SL2. When I tried to open the car with the key, the alarm went off and I can't get it to stop. I lost my keyless entry. What do I do to bypass the alarm, so I...


There should be an alarm fuse, you can pull that to shut it off. A GM dealer should be able to set you up with a new keyless entry remote. I'm not sure which fuse it is, but the service manual should tell you. If not, the fuse block cover may tell you as well. Good luck

Dec 03, 2010 | 1999 Saturn SL

2 Answers

1995 GMC Jimmy Keyless remote location


Make sure the place you are looking is under the steering wheel, not just the dash. The panel can be removed under the steering wheel and the connector can be shorted out. You should see a red connector or red wire. If rewiring was done, you might need to find a flashlight and follow every wire that is attached to any connector under the steering wheel. You should be able to pull the wires out enough to get a good look.

Good luck

Jun 21, 2008 | 1995 GMC Jimmy

1 Answer

2007 gmc yukon. Keyless Entry problem. The remote quit working but the gmc place said its not the battery. Help


Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

May 20, 2010 | Cars & Trucks

2 Answers

How can i tell if my 1990 gmc 1500 has keyless entry


All pre 1995 GMC vehicles had to have an alarm system to have keyless entry... So, lift the hood and look for a red LED near the right front of the vehicle. If none - you don't have keyless... if yes, the you do.... and an alarm system too.

Dec 31, 2009 | 1990 GMC Sierra

1 Answer

Does truck have keyless entry installed by factory


Write down the VIN# and take it to the dealer. They would be able to tell you if it did or didn't come with factory keyless entry.

Sep 07, 2009 | 2005 GMC Canyon

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.


Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Jun 17, 2009 | 2000 GMC Sierra

1 Answer

Keyless remote entry does not function, panic button does.


This link will take you to very good instructions try it worked for me www.wikihow/program-a-keyless-entry-for-a-chevy-silverado this works on GMC models also.

Mar 30, 2009 | 1999 GMC Sierra

Not finding what you are looking for?
2002 GMC Envoy Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...