Question about 2002 Ford F250 Super Duty SuperCab

1 Answer

Remote lock problem

I have a problem with the keyless remote it just stopped working tried to reprogram it but did not work I know I did it right because I just did a friends at work I can here it clicking but will not unlock or lock the lights blink and horn sounds but very weak could it be a sensor or a bad fuse. oh yeah you can unlock it with the lock unlock button inside the truck so I don't think it woul be a fuse. HELP

Posted by on

  • geraldo14200
    geraldo14200 Apr 04, 2009

    I have the same problem after AAA tried to unlock my doors with luck. I bought another keyless remote, programmed it and the keyless entry door locks still don't work. I checked all the fuses etc. maybe the reciever is bad?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

If the key less remote has been used alot, the remote inside has a bad connection. Same problem with my 97 pontiac grand prix took it a part and put a piece of paper behind the little chip and worked fine after. Not sure the same with yours but had same experience. Take a part the key less remote and clean the chip and try it with it a part. May be the solution maybe not just had the same problem but mine never worked no lights or nothing until I took it aprt and cleaned it.

Posted on May 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless receiver


immobilizer control module under the dash.some vechicles if you replace key remote dealership has to reprogram remotes using diagnostic equipment.try this techinique to synchronize remote transmitter. stand within 5 feet from vechicle .press transmitter lock and unlock buttons simultaneously for 7 seconds . system will lock and unlock doors confirming synchronization. if this dont help dealership has to reprogram remotes.

Dec 13, 2013 | 1997 Chevrolet Blazer

1 Answer

1999 toyota 4runner keyless remote doesn't work


Check with a Toyota dealer for your info

Aug 30, 2012 | 1999 Toyota 4Runner

1 Answer

My keyless entry pad stopped working replaced the battery and still will not work. I have a 2001 ford taurus ses. how do i resolve this problem by reprogramming the keyless entry pad? I tried the code lock...


Try it with a new remote pad, turn the key back and forth untill the locks jump up and down.. do it slowly , when they jump make sure to leave the key in the on position while pressing both lock and unlock buttons on the remote, they should then jump again telling you that the remote is now programed.

Apr 14, 2011 | Ford Taurus Cars & Trucks

1 Answer

I have recently purchased an 97 suburban it comes with a remote starter but i hae tried to start it via the remote and nothing happens i know that its soposed to work cause its the ltz model thanks for...


if you know the battery in the remote is good, you may need to reprogram the remote. does your keyless entry work? are they both on the same remote? ive reprogramed a replacement keyless entry for a 97 by using a short jumper wire on the obd II plug. you have to jump two of the pins and then hit the remote button a few times till it locks/unlocks then its synced. off hand i dont remeber which pins but google is your friend. not sure if this will also work on the remote start, if they use the same remote than it should.

Feb 21, 2011 | Chevrolet Suburban Cars & Trucks

2 Answers

Keyless remote not working


dead battery? Might need to be reprogrammed. Have all remotes handy before doing this.... insert key into ignition and turn the ignition on/off eight times in less than 20 seconds, leaving it "on" the eighth time. The locks might lock/unlock to let you know it is in program mode. Now press a button on each remote. The locks might lock/unlock again. All Done.
Try the battery first.

Jan 08, 2011 | Jaguar S-Type Cars & Trucks

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Ford 2000 Taurus, Keyless entry remote no longer works. Changed battery no luck. Tried reprograming and found door locks did not cycle open closed. Could not go further. Any ideas? Thanks, Al


I have a 2000 ford Taurus and my keyless remote has stopped working and having problems with key unlocking the door from outside, none of the remote work do u have any idea what my problem could be ?

Jul 30, 2009 | Ford Taurus Cars & Trucks

1 Answer

How do I reprogram my Keyless remote for Chevy malibu 2001


You need to take your car to a chevy dealer because they have the procedure for that, if tou call they wont help you by phone, they charge afee for that.

Jul 10, 2009 | 2000 Chevrolet Malibu

2 Answers

Door handle stuck


need to remove door panel either the linkage clip either broke or disconnected --if have remote start on fob need dealer to program--if normal try these links
Lexus Free Keyless Remote Fob Entry programming instructions Free Keyless Remote Fob Entry programming instructions procedures for all...

May 13, 2017 | 1998 Volvo V70

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...