Question about 1992 Saturn SC

1 Answer

Automatic seat belt removal and replace with regular seat belts

1992 Saturn SC with automoatic seat belts, how hard would it be to replace them with regular three point seat belts?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

You'd need to pickup the need parts at the junkyard. You'll need the "A" to "B" pillar trim, lower "B" pillar trim, front seat belts and seatbelt giude from a 1995 SC1 or SC2.

The treaded hole in the frame of the car where the track of the automatic seatbelt assembly attaches is in a slightly different place than the three point system. Its not a problem though. You just need to drill a 3/4" hole slightly above the existing hole in the trim panel. The existing hole is hidden by the seatbelt and not noticable at all.

Everything else pretty much bolts or snaps into place.

I've done this swap on several 1991-1994 Saturn S-Series.

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air bag light on! i want to check out the drivers seat, shoulder belt and lap belt with an ohm meter


first check fuse than check wiring/connections ground under seat than check sensor under front bumper as well as steering wiring

Aug 02, 2015 | 1994 Saturn Sc

1 Answer

How can i remove rear seats from my 2011 Vauxhall Insignia, also replace offside rear seat belt as I have had a mouse bite through the belt and the back seat


shoot the mouse !!!! ,,,, sorry coldnt resist ,,, you have to lift rear seatbase and boot carpet to get at the seat back bolts ,,, not a big problem ,,, the big one is getting at the seat belt because u have to remove alot of trim to get at the seat belt bolts ,,, alot of clips are involved that will break so source new clips before you start the job ,,,,rotten job so feel so sorry for you ,,,,

Dec 06, 2013 | 1992 Saturn SC

1 Answer

I cannot reach pulley bolt on my 2002 saturn any suggestions on how to reach it to replace belt


You have to jack up the right side of the vehicle, remove the right tire and the wheel well covering in order to gain easier access to the right side of your engine compartment in order to change the serpentine belt. I have changed the serpentine belt on my 2002 SC-1 Saturn without doing this, but you have to be very patient because there is only about 2 inches of clearance to work. A long handled box wrench works for me on the tensioner bolt when removing the belt.

Oct 21, 2013 | 2001 Saturn SL

1 Answer

Where is the seat belt motor in a 1991 saturn sc


Remove the pillar moldings "b" and the trim along the track. There are 10 mm nuts and bolts holding the track. The motor is in the bottom of the "B" pillar

Jan 16, 2010 | 1992 Saturn SC

1 Answer

My automatic seat belts are stuck around the halfway mark, how would I get them into the driving position? the Car is a 1991 saturn SL2 Sedan.


Probably best to replace, when the mechanism gets unreliable do not risk fixing try a wreckers yard, make sure the replacements pull out cleanly but lock when "jerked" hard.

Dec 15, 2009 | 1991 Saturn SL2

2 Answers

Altinator belt


The belt, most likely is shot...just get it replaced. Your car comes equipped with a "tensioner" pulley that keeps the belt tight all the time. Unless you have mechanical experience, I really do NOT recommend trying this job at home...Just DON'T GO TO THE DEALERSHIP!
Good Luck

Jun 23, 2009 | 1992 Saturn SC

1 Answer

Can you show me a picture of diagram of engine of saturn 1992 sc i need to know where the altinator is located


You should see it if you stand in front of car, look at the belts behind radiator fan, look to the top of those belts and it should be to the left with a belt hooked to it.

Jun 23, 2009 | 1992 Saturn SC

1 Answer

I have a 1993 saturn sc and it has automatic seatbelts that go across you.. and the drivers side works fine but the passenger side will not work. it stays up and when i close the door it is supposed to...


It Needs Either a New Seat belt track assy. on the side that's not working or a new Seat Belt Control module Located under center console (Blk Box With 3 Connectors) One Fuse works both tracks

May 09, 2009 | 1993 Saturn SC1

1 Answer

Belt tensioner assmebly went bad


Take the Right hand front wheel off, remove the plastic splash panel. Obviously, first remove tne belt. the tensioner should be slightly up in the wheel opening. Remove the pully, center bolt, remove the bolts attaching the tensioner asm. Local autoparts store should have replacement for around $30.00. Replace follow instructions backwards. While at auto store reference saturn manual for torque to tighten bolts when replacing. Do not over torque into aluminum block.

Apr 01, 2009 | 1992 Saturn SL

Not finding what you are looking for?
1992 Saturn SC Logo

1,425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...